18
GB
19 Check damaged parts
- Before further use of tool, it should be care-
fully checked to determine that it will operate
properly and perform its intended function.
- Check for alignment of moving parts, bind-
ing of moving parts, breakage of parts,
mounting and any other conditions that may
affect its operation.
- A guard or other part that is damaged
should be properly repaired or replaced by
an authorized service centre unless other-
wise indicated in this instruction manual.
- Have defective switches replaced by an au-
thorized service centre.
- Do not use the tool if the switch does not
turn it on and off.
20
DANGER!
- Special care must be taken with double mi-
tre cuts.
21 WARNING!
- The use of any accessory or attachment oth-
er than one recommended in this instruction
manual may present a risk of personal injury.
Service
a)
Have your tool repaired by a qualified person.
This electric tool complies with the relevant
safety rules. Repairs should only be carried
out by qualified persons using original spare
parts, otherwise this may result in consider-
able danger to the user.
ADDITIONAL SAFETY INSTRUCTIONS FOR TILE
CUTTING MACHINES
•
Set up the machine on a level, non-slip floor. Make
sure that the machine does not wobble.
• Check that the voltage on the rating plate is the sa-
me as your supply voltage. Only then are you to
insert the power plug in the socket-outlet.
• Wear safety goggles.
• Wear ear-muffs.
• Wear safety gloves.
• Never use cracked diamond cutting wheels. Repla-
ce immediately.
• Never use segmented cutting wheels.
• Caution! The cutting wheel runs on after the ma-
chine is switched off!
• Never apply side pressure to the diamond cutting
wheel in order to bring it to a halt.
• Caution! The diamond cutting wheel must be
cooled with water at all times.
• Always pull out the power plug before chan-ging
the cutting wheel.
• Use only suitable diamond cutting wheels.
• Never leave the machine unattended in rooms with
children.
• Always pull out the power plug before exami-ning
the electric motor compartment system
• Disorder in the work area can easily lead to acci-
dents.
• Make sure that you stand squarely and solidly
while working. Avoid abnormal body positions and
always keep your balance.
• If the cutting wheel becomes jammed, switch off
the equipment and disconnect it from the power
supply; only then are you to remove the workpiece.
Danger! Laser radiation Do not look in-
to the beam.
Laser class 2
Protect yourself and you environment from acci-
dents using suitable precautionary measures!
•
Do not look directly into the laser beam with the
naked eye.
•
Never look directly into the laser path.
•
Never direct the laser beam at reflecting sur-faces,
persons or animals. Even a low output laser beam
can inflict injury on the eye.
•
Caution: It is vital to follow the work procedu-res
described in these instructions. Using the tool in
any other way may result in hazardous exposure
to laser radiation.
•
Never open laser module.
•
When the tool is not going to be used for an ex-
tended period of time, the batteries should be re-
moved.
Residual risks
Even if you use this electric power tool in accordance
with instructions, certain residual risks cannot be rules
out. The following hazards may arise in connection
with the equipment’s construction and layout:
1.
Intervention in the running diamond cutting disc.
2.
Contact with the diamond cutting disc in expo-
sed area.
3.
Ejection of work pieces and work piece com-
ponents.
4.
Ejection of a faulty diamond attachment in the
cutting disc.
5.
Injuries to the eyes due to non-use of eye pro-
tection
6.
Health damage caused by hand-arm vibrations
if the equipment is used over a prolonged period
or is not properly guided and maintained.
7.
Remaining hazards can be minimized by follow-
ing the instructions in Safety Precautions, Proper
Use and in the entire operating manual.
Warning!
This electric tool generates an electro-
magnetic field during operation. This field can impair
active or passive medical implants under certain
conditions. In order to prevent the risk of serious or
deadly injuries, we recommend that persons with
medical implants consult with their physician and the
manufacturer of the medical implant prior to operat-
ing the electric tool.
