www.scheppach.com /
service@scheppach.com /
+(49)-08223-4002-99 /
+(49)-08223-4002-58
16 | GB
We accept no liability for damage or accidents which
arise due to non-observance of these instructions
and the safety information.
2. Device description(Fig. A - E)
1. Motor housing
2. On / Off switch
3. Handle
4.
Oil fill opening / sight glass
5. Additional handle
6. Tool holder
7. Point chisel
8. Locking bolt
9. Clamping screw
10. Locking screw
3. Scope of delivery
• (1x) Demolition Hammer
• (1x) Point chisel
• (1x) Flat chisel
• (1x) Oil can
• (1x) Carrying case
• (1x) Mounting key
• (2x) Carbon brushes
• (1x) Operating manual
4. Proper use
The machine is intended for heavy chiselling and
demolition work as well as for driving in and compact-
ing with the appropriate accessories.
The equipment is allowed to be used only for its pre-
scribed purpose. Any other use is deemed to be a
case of misuse. The user/operator and not the manu-
facturer will be liable for any damage or injuries of any
kind resulting from such misuse.
An element of the intended use is also the obser-
vance of the safety instructions, as well as the as-
sembly instructions and operating information in the
operating manual.
Persons who operate and maintain the machine must
be familiar with the manual and must be informed
about potential dangers.
In addition, the applicable accident prevention regula-
tions must be strictly observed.
Other general occupational health and safety-related
rules and regulations must be observed.
The liability of the manufacturer and resulting dam-
ages are excluded in the event of modifications of the
machine.
The machine may be operated only with original parts
and original accessories of the manufacturer.
The safety, work and maintenance instructions of the
manufacturer as well as the dimensions indicated in
the Technical Data section must be adhered to.
1. Introduction
Manufacturer:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
Dear customer,
We hope your new tool brings you much enjoyment
and success.
Note:
According to the applicable product liability laws, the
manufacturer of the device does not assume liability
for damages to the product or damages caused by
the product that occurs due to:
• Improper handling
• Non-compliance of the operating instructions
• Repairs by third parties, not by authorized ser-
vice technicians▪Installation and replacement of
non-original spare parts
•
Application other than specified
• A breakdown of the electrical system that occurs
due to the non-compliance of the electric regu-
lations and VDE regulations 0100, DIN 57113 /
VDE0113
We recommend:
Read through the complete text in the operating in-
structions before installing and commissioning the
device. The operating instructions are intended to
help the user to become familiar with the machine
and take advantage of its application possibilities in
accordance with the recommendations.
The operating instructions contain important informa-
tion on how to operate the machine safely, profes-
sionally and economically, how to avoid danger, cost-
ly repairs, reduce downtimes and how to increase
reliability and service life of the machine.
In addition to the safety regulations in the operating
instructions, you have to meet the applicable regu-
lations that apply for the operation of the machine in
your country. Keep the operating instructions pack-
age with the machine at all times and store it in a
plastic cover to protect it from dirt and moisture. Read
the instruction manual each time before operating the
machine and carefully follow its information.
The machine can only be operated by persons who
were instructed concerning the operation of the ma-
chine and who are informed about the associated
dangers. The minimum age requirement must be
complied with.
In addition to the safety notes contained in the pres-
ent operating instructions and the special regulations
of your country, the generally recognized technical
rules for the operation of woodworking machines
must be observed.
