www.scheppach.com
GB | 27
In addition, the applicable accident prevention regula-
tions must be strictly observed.
Other general occupational health and safety-related
rules and regulations must be observed.
The liability of the manufacturer and resulting damages
are excluded in the event of modifications of the ma
-
chine.
The machine may only be operated with original parts
and original accessories from the manufacturer.
The safety, operating and maintenance specifications
of the manufacturer, as well as the dimensions speci-
fied in the technical data, must be observed.
Please note that our equipment was not designed with
the intention of use for commercial or industrial purpos-
es. We assume no guarantee if the device is used in
commercial or industrial applications, or for equivalent
work.
The device is intended for use by adults. Children un-
der the age of 16 may only use the device when su-
pervised. The manufacturer is not liable for damage
caused by improper use or incorrect operation.
Only use the device as described and for the specified
areas of application. The device is not designed for
commercial use.
Any other use or modification shall be
deemed to be improper use and could give rise to con-
siderable risk of accident. The manufacturer assumes
no liability for damage arising from inappropriate use.
5. General safety instructions
Attention!
The following basic safety measures must
be observed when using electric tools for protection
against electric shock, and the risk of injury and fire.
Read all these notices before using the electric tool
and store the safety instructions well for later refer-
ence.
Safe work
1 Keep the work area orderly
– Disorder in the work area can lead to accidents.
2
Take environmental influences into account
– Do not expose electric tools to rain.
– Do not use electric tools in a damp or wet en-
vironment.
– Make sure that the work area is well-illuminated.
– Do not use electric tools where there is a risk of
fire or explosion.
3 Protect yourself from electric shock
– Avoid physical contact with earthed parts (e.g.
pipes, radiators, electric ranges, cooling units).
• Pressure bar holder (2e)
• 2x Horizontal stop support (2h)
• Moving stop (2c)
• Stop base body (2f)
• Front pressure bar (9)
• Front pressure bar holder with screws (9a)
• Suction adapter (12)
• 2x Wooden push block
• Transverse cutting gauge (10)
• Protective cover with alignment pin (13)
• 6x Hexagonal socket screw M5 x 20 (m)
• 8x Hexagonal socket screw M5 x 12 (l)
• 2x Hexagonal socket screw M6 x 16 (g)
• 2x Hexagonal bolt M6 x 40 (c)
• 6x Coach bolt M6 x 20 (f)
• 2x Coach bolt M6 x 25 (d)
• 5x Coach bolt M6 x 35 (e)
• 2x Knurled screw M6 (a)
• 15x Washer Ø 6 (h)
• 14x Washer Ø 5 (n)
• 10x Knurled nut M6 (b)
• 2x Wing nut M6 (i)
• 2x Nut M6 (j)
• 8x Nut M5 (o)
• Allen key - size 4 (k)
• Combination spanner SW18
• Combination spanner SW24
• Table width extension mounting device (11)
• Tool receiver Ø 6 / 8 / 12
• Operating manual
4. Proper use
The machine is only intended for the following activi-
ties: processing wood and plastic materials, such as:
milling grooves, working out recesses, copying curves
and lettering within the specified machine limits.
The
milling machine must not be used for working on metal,
stone, etc.
The machine may only be used in the intended manner.
Any use beyond this is improper. The user/operator, not
the manufacturer, is responsible for damages or inju-
ries of any type resulting from this.
An element of the intended use is also the observance
of the safety instructions, as well as the assembly in-
structions and operating information in the operating
manual.
Persons who operate and maintain the machine must
be familiar with it and must be informed about potential
dangers.
