19
GB
•
Do not allow children or any person who has not
read this instruction leaflet or who is not familiar with
the shredder to operate it.
•
The operator is responsible for third parties while
working with the shredder.
•
Only use the shredder for its intended purposes.
m
Caution! There are rotating blades on this ma-
chine.
m
Caution! Blades do not stop immediately after
switching off.
•
Always switch off the shredder, disconnect the plug
and wait until the cutting disc stops before carrying
out maintenance or cleaning work.
•
It is forbidden to move or modify any of the electrical
and mechanical safety devices.
•
Use only in daylight or good artificial light.
•
Do not put your hands into the feed funnel or ejec-
tion slot.
•
If the shredder should start to vibrate abnormally,
switch off the motor and check for the cause imme-
diately. Vibration is generally a warning of trouble.
•
Ensure blades are secure before shredding. Do not
operate the shredder if any of the blades are not
properly mounted.
•
The shredder should be checked carefully before
use. You should only work with a shredder that is in
good condition. If you notice any defect on the ma-
chine that may cause danger to the operator, do not
operate the shredder until defects are rectified.
•
Replace worn or damaged parts for safety. Use only
original spare parts. Parts not produced by manufac-
turer may cause poor fit and possible injury.
•
Use the shredder only in places where it is pro-
tected from water and never use it outdoors in rainy
weather.
•
Store in a dry secure place out of reach of children,
•
This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervi-
sion or instruction concerning use of the appliance
by a person responsible for their safety.
•
Children should be supervised to ensure that they
do not play with the appliance.
5.7 Preparation
•
Do not allow children to operate this equipment
•
Do not operate this equipment in the vicinity of by-
standers
•
Wear ear protection and safety glasses at all times
while operating
•
Avoid wearing clothing that is loose fitting or that has
hanging cords and ties
•
Only operate the machine the machine in open
space (e.g. Not close to a wall or other fixed objects)
and on a firm, level surface
•
Do not operate the machine on a paved or gravel
surface, where ejected material could cause injury
•
Before starting the machine, check that all screws,
nuts, bolts, and other fasteners are properly secured
and that guards and screens are in place. Replace
damaged and unreadable labels
6. Technical data
Dimensions
L x W x H mm
540x455x920mm
Rated Voltage AC
230V
Rated Frequency
50Hz
Rated Power
2500W (S6, 40%)
Rotation speed
4050min
-1
Max cutting diameter
40mm
Collect box
50l
Int.protection degree
IP44
Weight
14kg
Subject to technical changes!
I
nformation concerning noise emission measured
according to relevant standards:
Sound pressure L
pA
= 95,7 dB(A)
Guaranteed sound power L
WA
= 111 dB(A)
Uncertainty K
PA
= 3 dB(A)
Wear ear-muffs.
The impact of noise can cause damage to hearing.
7. Before starting the equipment
•
m
Warning! You may need assistance when lifting
the machine out of the box and assembling.
Open the package and remove the machine from
package;Pull out the collect box and take out the main
part of the machine and all accessories;
7.1 Assembly of the shredder (Fig. 4)
•
Turn the shredder upside down.
•
Pivot the legs upward, place the supplied wheel axle
through the respective openings.
•
Insert the screws through the black plastic and
screw tight.
•
Place the supplied sleeves on the wheel axles. Then
the wheels, the pinion and,finally, the lock nut with
the wheel cover.
• m
Warning! Take care when tilting the unit onto
its wheels as the unit has an uneven weight dis-
tribution when tilted and during wheeled trans-
portation.
7.2 Collect box (Fig. 3)
Push the collect box into the undercarriage after
pushing the lock button (6) upward.
