www.scheppach.com
GB | 43
Note:
The oil level must be checked with the splitting blade
retracted. The oil dipstick is located beneath the split-
ting table in filler plug A (Fig.
8)
and is marked with 2
notches.
If the oil level lies at the bottom notch then this
is the minimum oil level.
If this is the case, the oil must
be topped up immediately.
The top notch indicates the
maximum oil level.
The splitting column must be retracted before the
check, the machine must be level.
When do I change the oil?
First oil change after 50 operating hours, then every
500 operating hours.
Oil change, Fig. 14
•
Fully retract the splitting column.
•
Place a container with at least 8 litres capacity under
the splitter.
•
Loosen the ventilation flap A
• Open the drain screw B so that oil can run out.
•
Close the drain screw again and tighten securely.
•
Fill with 8 l of new hydraulic oil using a clean funnel.
• Screw the ventilation cap back on again.
Dispose of the used oil properly at a local used oil
collection point. Dumping used oil in the soil or
mixing it with waste is prohibited.
We recommend the following hydraulic oils:
• Aral Vitam gf 22
•
BP Energol HLP-HM 22
•
Mobil DTE 11
• Shell Tellus 22
• or equivalent.
Do not use other types of oil!
The use of other oils affects the function of the hydrau
-
lic cylinder.
Splitter spar
The spar of the splitter must be lightly greased before
commissioning.
This process must be repeated every
5 operating hours.
Apply grease or spray oil lightly.
The
spar must not run dry.
Hydraulic system
The hydraulic system is a closed system with an oil
tank, oil pump and control valve
The factory-completed system must not be changed or
manipulated.
When connecting to the mains or in the event of the
machine being moved to another location, the turning
direction must be checked.
It may be necessary to
change the polarity.
Turn the pole changing device (400 V) in the device
connector.
(Fig.
15).
11. Cleaning, maintenance and repair
Attention!
Pull out the mains plug before carrying out all cleaning,
maintenance and repair work.
Only carry out modifications, adjustments and cleaning
work when the motor is switched off.
Experienced craftsmen can carry out small repairs on
the machine themselves.
Repair and maintenance work on the electrical
system may only be carried out by qualified elec-
tricians.
All protective and safety equipment must be reas-
sembled immediately after repair, maintenance is
completed.
Our recommendation to you:
•
Clean the machine thoroughly after each use!
•
Riving knife
- The riving knife is a wearing part that must be re-
sharpened if necessary.
• Two-hand protective guard
- The combined retaining and control device must
remain smooth-running. Lubricate with a few
drops of oil as required.
•
Moving parts
- Keep the splitting blade guides clean.
(fouling,
wood chippings, bark, etc.)
-
Lubricate slide rails with spray oil or grease
•
Check the hydraulic oil level.
-
Check hydraulic connections and screw connec
-
tions for tightness and wear. Tighten the screw
connections if necessary.
Check the oil level
The hydraulic system is a closed system with an oil
tank, oil pump and control valve. Check the lubricating
oil level regularly before commissioning.
An oil level
that is too low can damage the oil pump.
Summary of Contents for 5905421902
