www.scheppach.com
44 | GB
12. Transport
Transport by hand, Fig.
10
To transport the log splitter, the riving knife (3) must be
moved all the way down.
Tilt the splitter with the handle
(1) on the splitting column until the machine is on the
support wheel (26) and can therefore be moved.
Transport by crane Fig.11
Attach the belt to the holder on the left of the upper
hoop guard and to the holder on the right of the locking
lever and carefully lift the machine!
Never lift on the riving knife!
13. Storage
In the event of storage, observe the following condi
-
tions:
•
dry, covered storage location
•
max. humidity 80%
• Temperature from -20 °C to +60 °C
The machine should operate in the following environ-
mental conditions:
Minimum
Maximum
Recommended
Temper-
ature
5 C°
40 C°
16 C°
Humidity
95 %
70 %
Store the power tool in its original packaging.
Cover the power tool to protect it from dust or moisture.
Store the operating manual with the power tool.
14.
Disposal and recycling
The device is supplied in packaging to avoid
transport damages. This packaging is raw
material and can thus be used again or can
be reintegrated into the raw material cycle.
The device and its accessories are made
of different materials, such as metals and
plastics. Take defective components to special waste
disposal sites.
Check with your specialist dealer or mu
-
nicipal administration!
The machine does not contain any substances that are
harmful to health or the environment, as it has been
constructed from materials that are fully recyclable or
can be disposed of in the normal way.
Check the oil level regularly.
An oil level that is too low will damage the oil pump.
Regularly check hydraulic connections and screw con
-
nections for leaks –
retighten if necessary
.
Before starting the maintenance or checks, clean the
work area and have suitable tools at hand and in good
condition.
The time intervals cited here relate to normal operating
conditions. If the machine is subjected to heavier loads,
these times must be reduced accordingly.
Clean the machine cladding, panels and control levers
with a soft, dry cloth or a cloth that has been slightly
moistened with neutral cleaning agent. Do not use any
solvents such as alcohol or petrol as these may dam
-
age the surfaces.
Keep oils and lubricants out of reach of unauthorised
persons. Read through the instructions on the con
-
tainers carefully and follow them closely. Avoid direct
contact with the skin and wash off thoroughly after use.
Connections and repairs
Connections and repair work on the electrical equip-
ment may only be carried out by electricians.
Please provide the following information in the
event of any enquiries:
•
Type of current for the motor
•
Data of machine type plate
•
Data of motor type plate
Service information
With this product, it is necessary to note that the follow
-
ing parts are subject to natural or usage-related wear,
or that the following parts are required as consuma-
bles.
Wearing parts*:
Riving knife
* may not be included in the scope of supply!
Spare parts and accessories can be obtained from our
service centre.
To do this, scan the QR code on the
cover page.
Summary of Contents for 5905421902
