24
GB
1. Introduction
MANUFACTURER:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
DEAR CUSTOMER,
We hope your new tool brings you much enjoyment
and success.
NOTE:
According to the applicable product liability laws, the
manufacturer of the device does not assume liability
for damages to the product or damages caused by
the product that occurs due to:
•
Improper handling,
•
Non-compliance of the operating instructions,
•
Repairs by third parties, not by authorized service
technicians,
•
Installation and replacement of non-original spare
parts,
•
Application other than specified,
m
Important! We recommend:
Read through the complete text in the operating in
-
structions before installing and commissioning the
device. The operating instructions are intended to
help the user to become familiar with the machine
and take advantage of its application possibilities in
accordance with the recommendations. The operat
-
ing instructions contain important information on how
to operate the machine safely, professionally and
economically, how to avoid danger, costly repairs, re
-
duce downtimes and how to increase reliability and
service life of the machine.
In addition to the safety regulations in the operating
instructions, you have to meet the applicable regula
-
tions that apply for the operation of the machine in
your country. Keep the operating instructions pack
-
age with the machine at all times and store it in a
plastic cover to protect it from dirt and moisture.
Read the instruction manual each time before op
-
erating the machine and carefully follow its informa
-
tion. The machine can only be operated by persons
who were instructed concerning the operation of the
machine and who are informed about the associated
dangers. The minimum age requirement must be
complied with.
We assume no liability for accidents or damages
resulting by disregarding these instructions and the
safety instructions.
2. Layout (Fig. 1)
1
Operating lever
2
Cylinder
3
Wheels
4
Return bracket
5
Supporting arm
6
Splitting blade
7
Three-point suspension
8
Log lifter
9
Chain
10
Drive shaft
11
Transport lug
3. Scope of delivery
•
Open the packaging and remove the device care
-
fully.
•
Remove the packaging material as well as the
packaging and transport bracing (if available).
•
Check that the delivery is complete.
•
Check the device and accessory parts for trans
-
port damage.
•
If possible, store the packaging until the warranty
period has expired.
ATTENTION
The device and packaging materials are not toys!
Children must not be allowed to play with plas-
tic bags, film and small parts! There is a risk of
swallowing and suffocation!
Fig. 2:
1.
Kindling splitter frame & tractor unit
2.
Supporting arm
3.
Log lifter
4.
Hook
5.
Drive shaft protective cap
6.
Three-point suspension bolt
7.
Operating instructions
8.
Bag with small parts
4. Intended use
The wood splitter has only been designed to split
wood in the fibre direction. Respecting technical data
and safety precautions. When splitting, it is essential
to make sure the split wood only contacts the check
-
ered sheet of the bottom plate.
The hydraulic log splitter can only be used in a verti
-
cal position. Logs may only be split along the direc
-
tion of the fiber. Log dimensions are:
Log lengths max. 110 cm
Ø min. 12 cm, max. 60 cm
Never split logs in horizontal position or against
the direction of the fiber.
1.
The equipment is to be used only for its prescribed
purpose. Any other use is deemed to be a case
of misuse.
Summary of Contents for 5905501903
