www.scheppach.com
GB | 23
21 Place of installation
- Set up the compressor on an even surface.
22
Supply hoses at pressures above 7 bar should be
equipped with a safety cable (e.g. a wire rope).
23
Avoid over-stressing the piping system by using
flexible hose connections to prevent kinking.
24
Use a residual current circuit breaker with a trigger
current of 30 mA or less. Using a residual current
circuit breaker reduces the risk of an electric shock.
25. Ensure that oil cooling devices are kept clean and
protective devices remain in operational condition.
26.
Risk of burns from hot oil
-
Wear suitable protective gloves.
- Never work with the compressor near naked
flames.
- Be careful not to spill oil.
27.
Motor start-up is prohibited at low temperatures be
-
low 0 °C.
m
WARNING!
This electric tool generates an elec-
tromagnetic field during operation. This field can im
-
pair active or passive medical implants under certain
conditions. In order to prevent the risk of serious or
deadly injuries, we recommend that persons with
medical implants consult with their physician and the
manufacturer of the medical implant prior to operating
the electric tool.
ADDITIONAL SAFETY INSTRUCTIONS
Safety instructions for working with compressed
air and blasting guns
•
The compressor pump and lines can become very
hot during operation. Touching these parts will burn
you.
•
The air which is sucked in by the compressor must
be kept free of impurities that could cause fires or
explosions in the compressor pump.
•
When releasing the hose coupling, hold the hose
coupling piece with your hand. This way, you can
protect yourself against injury from the rebound
-
ing hose.
•
Wear safety goggles when working with the blow-
out pistol. Foreign bodies or blown off parts can
easily cause injuries.
• Do not blow at people with the blow-out pistol and
do not clean clothes while being worn. Risk of in
-
jury!
14 Check the electric tool for potential damage
- Protective devices and other parts must be care-
fully inspected to ensure that they are fault-free
and function as intended prior to continued use of
the electric tool.
- Check whether the moving parts function fault-
lessly and do not jam or whether parts are dam
-
aged. All parts must be correctly mounted and all
conditions must be fulfilled to ensure fault-free
operation of the electric tool.
- Damaged protective devices and parts must be
properly repaired or replaced by a recognised
workshop, insofar as nothing different is specified
in the operating manual.
- Damaged switches must be replaced at a cus-
tomer service workshop.
-
Do not use any faulty or damaged connection
cables.
-
Do not use any electric tool on which the switch
cannot be switched on and off.
15
Have your electric tool repaired by a qualified
electrician
- This electric tool conforms to the applicable safe-
ty regulations. Repairs may only be performed by
an electrician using original spare parts. Other-
wise accidents can occur.
16 Important!
-
For your own safety you must only use the acces
-
sories and additional units listed in the operating
instructions or recommended or specified by the
manufacturer. The use of mounted tools or acces-
sories other than those recommended in the op-
erating instructions or catalogue may place your
personal safety at risk.
17 Noise
-
Wear ear muffs when you use the compressor.
18
Replacing the power cable
- To prevent hazards, leave the replacement of
damaged power cables strictly to the manufac
-
turer or a qualified electrician. There is a risk of
electric shock!
19
Inflating tires
-
Directly after inflating tires, check the pressure
with a suitable pressure gauge, for example at
your filling station.
20
Roadworthy compressors for building site oper
-
ations
-
Make sure that all lines and fittings are suitable
for the maximum permissible operating pressure
of the compressor.
Summary of Contents for 5906103901
