www.scheppach.com
service@scheppach.com
+(49)-08223-4002-99
+(49)-08223-4002-58
16 І 92
•
Check the pressure vessel for signs of rust and dam-
age each time before using. Do not use the com-
pressor with a damaged or rusty pressure vessel. If
you discover any damage, then please contact the
customer service workshop.
Do not lose these safety instructions
6. Technical data
Mains connection
220-240 V~ 50 Hz
Motor rating W
1100
Operating mode
S1
Compressor speed min
-1
2850 min
-1
Pressure vessel capacity (in liters)
approx. 24
Operating pressure
approx. 8 bar
Theoretical intake capacity (l/min)
approx. 165
sound power level L
WA
96 dB(A)
uncertainty K
WA
1,8 dB
Protection type
IP20
Weight of the unit in kg
20
The noise emission values were measured in accord-
ance with EN ISO 2151.
Wear hearing protection.
The effects of noise can cause a loss of hearing.
7. Before starting the equipment
Before you connect the equipment to the mains supply
make sure that the data on the rating plate are identical
to the mains data.
•
Check the equipment for damage which may have
occurred in transit. Report any damage immediately
to the transport company which was used to deliver
the compressor.
•
Install the compressor near the point of consumption.
•
Avoid long air lines and supply lines (extension ca-
bles).
•
Make sure that the intake air is dry and dustfree.
•
Do not install the compressor in a damp or wet room.
•
The compressor may only be used in suitable rooms
(with good ventilation and an ambient temperature from
+5 °C to 40 °C). There must be no dust, acids, vapors,
explosive gases or inflammable gases in the room.
•
The compressor is designed to be used in dry rooms.
It is prohibited to use the compressor in areas where
work is conducted with sprayed water.
8. Attachment and operation
n
Important!
You must fully assemble the appliance before using
it for the first time!
You will require the following tools for assembly and
installation: 2 x open-ended wrench size 17 mm (not
included)
21
Place of installation
–
Set up the compressor on an even surface.
ADDITIONAL SAFETY INSTRUCTIONS
Safety instructions for working with compressed
air and blasting guns
• The compressor pump and lines can become very hot
during operation. Touching these parts will burn you.
• The air which is sucked in by the compressor must
be kept free of impurities that could cause fires or
explosions in the compressor pump.
• When releasing the hose coupling, hold the hose cou-
pling piece with your hand. This way, you can protect
yourself against injury from the rebounding hose.
• Wear safety goggles when working with the blow-out
pistol. Foreign bodies or blown off parts can easily
cause injuries.
• Do not blow at people with the blow-out pistol and
do not clean clothes while being worn. Risk of injury!
Safety information for paint spraying
• Do not process any paints or solvents with a flash point
below 55° C. There is a risk of explosion!
• Do not heat up paints or solvents. There is a risk of
explosion!
• If hazardous liquids are processed, wear protective filter
units (face guards). Also, adhere to the safety informa-
tion provided by the manufacturers of such liquids.
• The details and designations of the Ordinance on Haz-
ardous Substances, which are displayed on the outer
packaging of the processed material, must be observed.
• Additional protective measures are to be undertaken if
necessary, particularly the wearing of suitable clothing
and masks.
• Do not smoke during the spraying process and/or in
the work area. There is a risk of explosion! Paint vapors
are easily combustible.
• Never set up or operate the equipment in the vicinity of
a fire place, open lights or sparking machines.
• Do not store or eat food and drink in the work area.
Paint vapors are harmful to your health.
• The work area must exceed 30 m
3
and sufficient ven-
tilation must be ensured during spraying and drying.
Do not spray against the wind. Always adhere to the
regulations of the local police authority when spraying
combustible or hazardous materials.
• Do not process media such as white spirit, butyl alcohol
and methylene chloride with the PVC pressure hose.
These media will destroy the pressure hose.
Operating pressure vessels
•
You must keep your pressure vessel in good working
order, operate the vessel correctly, monitor the vessel,
carry out necessary maintenance and repair work im-
mediately and meet the relevant safety precautions.
•
The supervisory authority may enforce essential con-
trol measures in individual cases.
•
A pressure vessel is not allowed to be used if it has
faults or deficiencies that can endanger workers or
third parties.
DE
GB
Heruntergeladen von
Handbücher-Suchmachiene
