Scheppach 59061129933, Original Instruction Manual



 www.scheppach.com / 



 service@scheppach.com / 



 +(49)-08223-4002-99 / 



 +(49)-08223-4002-58

16 | GB

7.  Wear suitable clothing

 - Do not wear wide clothing or jewellery, which 

can become entangled in moving parts.

 - Rubber gloves and non-slip shoes are recom-

mended when working outdoors.

 - Tie long hair back in a hair net.

8.  Do not use the cable for purposes for which it is 

not intended

 - Do not use the cable to pull the plug out of the 

outlet. Protect the cable from heat, oil and sharp 

edges.

9.  Take care of your tools

 - Keep your compressor clean in order to work 

well and safely.

 - Follow the maintenance instructions. 

 - Check the connection cable of the electric tool 

regularly and have it replaced by a recognised 

specialist when damaged.

 - Check extension cables regularly and replace 

them when damaged.

10. Pull the plug out of the outlet

 - During non-use of the electric tool or prior to 

maintenance and when replacing tools.

11. Avoid inadvertent starting

 -

Make sure that the switch is switched off when 

plugging the plug into an outlet.

 - Use extension cables for outdoors

12. 

Only  use  approved  and  appropriately  identified 

extension cables for use outdoors.

 - Only use cable reels in the unrolled state.

13. Remain attentive

 - Pay attention to what you are doing. Remain 

sensible when working. Do not use the electric 

tool when you are distracted.

14. Check the electric tool for potential damage

 - Protective devices and other parts must be care-

fully inspected to ensure that they are fault-free 

and function as intended prior to continued use 

of the electric tool.

 - Check whether the moving parts function 

faultlessly and do not jam or whether parts are 

damaged. All parts must be correctly mounted 

and all conditions must be fulfilled to ensure 

fault-free operation of the electric tool.

 - Damaged protective devices and parts must be 

properly repaired or replaced by a recognised 

workshop, insofar as nothing different is speci

-

fied in the operating manual.

 - Damaged switches must be replaced at a cus-

tomer service workshop.

 - Do not use any faulty or damaged connection 

cables.

 - Do not use any electric tool on which the switch 

cannot be switched on and off.

4.  Intended use

The compressor is designed to generate compressed 

air for compressed-air driven tools which can be driv-

en with an air volume of up to approx. 270 l/min (e.g. 

tire infl ator, blow-out pistol and paint spray gun). Due 

to the limited air output it is not possible to use the 

compressor to drive tools with very high air consump-

tion (for example orbital sanders, rod grinders and 

hammer screwdrivers).

The equipment is to be used only for its prescribed 

purpose. Any other use is deemed to be a case of 

misuse. The user / operator and not the manufacturer 

will be liable for any damage or injuries of any kind 

caused as a result of this.

Please note that our equipment has not been de-

signed for use in commercial, trade or industrial appli-

cations. Our warranty will be voided if the equipment 

is used in commercial, trade or industrial businesses 

or for equivalent purposes.

5.  Safety information

m 

ATTENTION! 

The following basic safety meas-

ures must be observed when using electric tools for 

protection against electric shock, and the risk of in-

jury and fire. Read all these notices before using the 

electric tool and keep the safety instructions for later 

reference.

Safe work

1.  Keep the work area orderly

 - Disorder in the work area can lead to accidents.

2. 

Take environmental influences into account

 - Do not expose electric tools to rain.

 - Do not use electric tools in a damp or wet envi-

ronment. There is a risk of electric shock! 

 - Make sure that the work area is well-illuminated.

 - Do not use electric tools where there is a risk of 

fire or explosion.

3.  Protect yourself from electric shock

 - Avoid physical contact with earthed parts (e.g. 

pipes, radiators, electric ranges, cooling units).

4.  Keep children away

 - Do not allow other persons to touch the equip-

ment or cable, keep them away from your work 

area.

5.  Securely store unused electric tools

 - Unused electric tools should be stored in a dry, 

elevated or closed location out of the reach of 

children.

6.  Do not overload your electric tool

 - They work better and more safely in the speci-

fied output range.