Scheppach 59061129933, Original Instruction Manual



 www.scheppach.com / 



 service@scheppach.com / 



 +(49)-08223-4002-99 / 



 +(49)-08223-4002-58

18 | GB

8.  Attachment and operation

n 

IMPORTANT!

You must fully assemble the appliance before us-

ing it for the first time!

You will require the following tools for assembly and 

installation: 2 x open-ended wrench size 17 mm (not 

included)

8.1 Fitting the wheels (10)

Fit the supplied wheels (10) as shown in Figure 5.

8.2 Fitting the supporting foot (7)

Fit the supplied supporting foot (A) as shown in Fig. 6.

8.3 Mains connection

The compressor is equipped with a mains cable with 

shock-proof plug. This can be connected to any 230-

240 V~ 50 Hz shock-proof socket which is protected 

by a 16 A fuse.

Before you use the machine, make sure that the 

mains voltage is the same as the operating voltage 

(see the rating plate).

Long supply cables, extensions, cable reels etc. cause 

a drop in voltage and can impede motor start-up.

At low temperatures below +5°C, sluggishness may 

make starting difficult or impossible.

8.4 ON/OFF switch (Fig. 2)

Pull the ON/OFF switch (12) upwards to switch on the 

compressor. To switch off the compressor, press the 

ON/OFF switch (12) down.

8.5 Setting the pressure: (Fig. 4)

Use the pressure regulator (3) to set the pressure on 

the pressure gauge (5).

The set pressure can be drawn from the quicklock 

coupling (Fig. 1/Pos. 4).

8.6 Setting the pressure switch

•  The pressure switch is set at the factory. Cut-in 

pressure approx. 6 bar Cut-out pressure approx. 

8 bar.

9.  Electrical connection

The electrical motor installed is connected and 

ready for operation. The connection complies 

with the applicable VDE and DIN provisions. The 

customer‘s mains connection as well as the ex-

tension cable used must also comply with these 

regulations.

Damaged electrical connection cable

The insulation on electrical connection cables is of-

ten damaged.

6.  Technical data

Mains connection

220-240 V~ 50 Hz

Motor rating

1100W

Operating mode

S1

Compressor speed

2850 min

-1

Pressure vessel capacity

approx. 24 l

Operating pressure

approx. 8 bar

Theoretical intake capac-

ity

approx. 165 l/min

Protection type

IP 20

Weight of the unit in kg

20 kg

Subject to technical changes!

Sound power level L

WA

97 dB(A)

Uncertainty K

wa/pA

 1,96 dB(A)

The noise emission values were measured in accord-

ance with EN ISO 2151.

Wear hearing protection.

The effects of noise can cause a loss of hearing.

7.  Before starting the equipment

Before you connect the equipment to the mains  sup-

ply make sure that the data on the rating plate are 

identical to the mains data.

•  Check the equipment for damage which may have 

occurred in transit. Report any damage immedi-

ately to the transport company which was used to 

deliver the compressor.

•  Install the compressor near the point of consump-

tion.

•  Avoid long air lines and supply lines (extension ca-

bles).

•  Make sure that the intake air is dry and dustfree.

•  Do not install the compressor in a damp or wet 

room.

•  The compressor may only be used in suitable rooms 

(with good ventilation and an ambient temperature 

from +5 °C to 40 °C). There must be no dust, acids, 

vapors, explosive gases or inflammable gases in the 

room.

•  The compressor is designed to be used in dry 

rooms. It is prohibited to use the compressor in ar-

eas where work is conducted with sprayed water.