www.scheppach.com /
service@scheppach.com /
+(49)-08223-4002-99 /
+(49)-08223-4002-58
18 | GB
m
ATTENTION
The device and packaging materials are not toys!
Children must not be allowed to play with plas-
tic bags, film and small parts! There is a risk of
swallowing and suffocation!
4. Intended use
The compressor is designed to generate com-
pressed air for compressed-air driven tools which
can be driven with an air volume of up to approx. 272
l/min (e.g. tire inflator, blow-out pistol and paint spray
gun).
The equipment is to be used only for its prescribed
purpose. Any other use is deemed to be a case of
misuse. The user / operator and not the manufactur-
er will be liable for any damage or injuries of any kind
caused as a result of this.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the equip
-
ment is used in commercial, trade or industrial busi-
nesses or for equivalent purposes.
5. Safety information
m
Attention!
The following basic safety measures
must be observed when using electric tools for pro-
tection against electric shock, and the risk of injury
and fire. Read all these notices before using the elec
-
tric tool and keep the safety instructions for later ref
-
erence.
m
Attention!
The following basic safety actions
must be taken when using this compressor in order
to protect the user from electric shocks and the risk
of injury and fi re. Read and follow these instructions
before using the equipment.
Safe work
1.
Keep the work area orderly
- Disorder in the work area can lead to accidents.
2.
Take environmental influences into account
- Do not expose electric tools to rain.
- Do not use electric tools in a damp or wet envi-
ronment. There is a risk of electric shock!
- Make sure that the work area is well-illuminated.
- Do not use electric tools where there is a risk of
fire or explosion.
3.
Protect yourself from electric shock
-
Avoid physical contact with earthed parts (e.g.
pipes, radiators, electric ranges, cooling units).
4.
Keep children away
- Do not allow other persons to touch the equip-
ment or cable, keep them away from your work
area.
5.
Securely store unused electric tools
-
Unused electric tools should be stored in a dry,
elevated or closed location out of the reach of
children.
6.
Do not overload your electric tool
-
They work better and more safely in the speci
-
fied output range.
7. Wear suitable clothing
-
Do not wear wide clothing or jewellery, which
can become entangled in moving parts.
- Rubber gloves and non-slip shoes are recom-
mended when working outdoors.
- Tie long hair back in a hair net.
8. Do not use the cable for purposes for which it is
not intended
- Do not use the cable to pull the plug out of the
outlet. Protect the cable from heat, oil and sharp
edges.
9.
Take care of your tools
-
Keep your compressor clean in order to work
well and safely.
- Follow the maintenance instructions.
- Check the connection cable of the electric tool
regularly and have it replaced by a recognised
specialist when damaged.
-
Check extension cables regularly and replace
them when damaged.
10. Pull the plug out of the outlet
- During non-use of the electric tool or prior to
maintenance and when replacing tools such as
saw blades, bits, milling heads.
11. Avoid inadvertent starting
-
Make sure that the switch is switched off when
plugging the plug into an outlet.
12. Use extension cables for outdoors
-
Only use approved and appropriately identified
extension cables for use outdoors.
-
Only use cable reels in the unrolled state.
13. Remain attentive
-
Pay attention to what you are doing. Remain
sensible when working. Do not use the electric
tool when you are distracted.
14. Check the electric tool for potential damage
- Protective devices and other parts must be care-
fully inspected to ensure that they are fault-free
and function as intended prior to continued use
of the electric tool.
- Check whether the moving parts function
faultlessly and do not jam or whether parts are
damaged.
-
All parts must be correctly mounted and all
conditions must be fulfilled to ensure fault-free
operation of the electric tool.
- Damaged protective devices and parts must be
properly repaired or replaced by a recognised
workshop, insofar as nothing different is speci
-
fied in the operating manual.
