www.scheppach.com /
service@scheppach.com /
+(49)-08223-4002-99 /
+(49)-08223-4002-58
22 | GB
20 Check the electric tool for damage
– Before using the electric tool, you must inspect
safety equipment or slightly damaged parts
carefully to ensure that they work properly and
as intended.
– Check to see that the moving parts operate
freely and don’t stick, and to make sure no parts
are damaged. All parts must be mounted prop-
erly and meet all the conditions for ensuring
trouble-free operation of the electric tool.
– Damaged safety equipment and parts must be
properly repaired or replaced by a professional
facility, unless otherwise indicated in the user
manual.
– Damaged switches must be replaced by a cus-
tomer service facility.
– Never use an electric tool whose switch cannot
be turned on and off.
21 CAUTION!
– Using other insertion tools and accessories
may cause injury.
22 Have your tool repaired by an electrical expert
– This electric tool meets applicable safety re-
quirements. Repairs must be made only by an
electrical expert using original replacement
parts. Otherwise accidents many occur.
23 Noise
– Wear ear muffs when you use the compressor.
24 Replacing the power cable
– To prevent hazards, leave the replacement of
damaged power cables strictly to the manufac-
turer or a qualified electrician. There is a risk
of electric shock!
25
Inflating tires
–
Directly after inflating tires, check the pressure
with a suitable pressure gauge, for example at
your filling station.
26 Roadworthy compressors for building site oper-
ations
–
Make sure that all lines and fittings are suitable
for the maximum permissible operating pres-
sure of the compressor.
27 Place of installation
– Set up the compressor on an even surface.
28 Supply hoses at pressures above 7 bar should be
equipped with a safety cable (e.g. a wire rope).
ADDITIONAL SAFETY INSTRUCTIONS
Safety instructions for working with compressed
air and blasting guns
• The compressor pump and lines can become
very hot during operation. Touching these parts
will burn you.
• The air which is sucked in by the compressor must
be kept free of impurities that could cause fires or
explosions in the compressor pump.
For example, do not use a portable circular saw
for cutting tree branches or logs.
8 Wear proper clothing
– Do not wear loose clothing or jewellery, as they
can get caught in moving parts.
– When working outdoors, wear slip-resistant
shoes.
– Wear a hairnet over long hair.
9 Use protective gear
– Wear safety glasses.
– Wear a breathing mask during work that cre-
ates dust.
10 Connect the dust extraction equipment
– If there are connections to dust extraction and
collection equipment, make sure that they are
connected and properly used.
11 Do not use the cable for purposes for which it was
not intended
– Never use the cable to pull the plug from the
socket. Protect the cable from heat, oil and
sharp edges.
12 Secure the work piece
– Use clamps or a vice to hold the work piece
firmly. They will hold it more securely than your
hand can.
13 Avoid abnormal postures
– Make sure to stand securely and always keep
your balance.
14 Maintain your tools with care
– For better and safer work, keep cutting tools
sharp and clean.
– Follow the instructions for lubrication and
changing tools.
– Regularly inspect the electric tool’s connection
cable, and if it is damaged, have it replaced by
an authorized expert.
– Regularly check extension cords, and replace
them if they are damaged.
– Keep the handles dry, clean and free of oil and
grease.
15 Pull the plug from the socket
– When not using the electric tool, before main-
tenance or when changing tools, such as saw
blades, drills and cutting bits.
16 Do not leave any tool keys inserted
– Before switching on, check to see that keys and
adjustment tools have been removed.
17 Avoid unintentional activation
– When plugging the tool in, make sure that the
switch is turned off.
18 Use outdoor extension cords
– When outdoors, use only extension cords that
are approved and appropriately marked.
– Only use cable reels in the unrolled state.
19 Be alert
– Pay attention to what you do. Approach your
work sensibly. Do not use the electric tool when
you are distracted.
