Scheppach 5906138901, Translation Of Original Instruction Manual



 www.scheppach.com / 



 service@scheppach.com / 



 +(49)-08223-4002-99 / 



 +(49)-08223-4002-58

28 | GB

m

 WARNING!

 This electric tool generates an elec-

tromagnetic field during operation. This field can im

-

pair active or passive medical implants under certain 

conditions. In order to prevent the risk of serious or 

deadly injuries, we recommend that persons with 

medical implants consult with their physician and the 

manufacturer of the medical implant prior to operat-

ing the electric tool.

ADDITIONAL SAFETY INSTRUCTIONS

Observe the corresponding operating manuals 

of the respective compressed air tools / com-

pressed air attachments! 

The following general 

warnings must also be observed.

Safety instructions for working with compressed 

air and blasting guns

• 

Ensure there is sufficient distance to the product, 

at least 2.50 m, and keep the compressed air tools 

/ compressed air attachments away from the com-

pressor during operation.

•  The compressor pump and lines can become very 

hot during operation. Touching these parts will burn 

you.

•  The air which is sucked in by the compressor must 

be kept free of impurities that could cause fires or 

explosions in the compressor pump.

•  When releasing the hose coupling, hold the hose 

coupling piece with your hand. This way, you can 

protect yourself against injury from the rebounding 

hose.

•  Wear safety goggles and a respirator when working 

with the compressed air pistol. Dusts are harmful 

to health! Injuries can be easily caused by foreign 

objects and blown away parts.

•  Do not blow at people with the blow-out pistol and 

do not clean clothes while being worn. Risk of in-

jury!

Safety instructions when using spraying attach-

ments (e.g. paint sprayers)

•  Keep the spray attachment away from the com-

pressor  when  filling  so  that  no  liquid  comes  into 

contact with the compressor.

•  Never spray in the direction of the compressor 

when using the spraying attachments (e.g. paint 

sprayers). Moisture can lead to electrical hazards!

• 

Do not process any paints or solvents with a fl ash 

point below 55 °C. Risk of explosion!

•  Do not heat up paints or solvents. Risk of explo-

sion!

•  If hazardous liquids are processed, wear protective 

filter units (face guards). Also, adhere to the safety 

information provided by the manufacturers of such 

liquids.

–

Check whether the moving parts function fault-

lessly and do not jam or whether parts are dam-

aged. All parts must be correctly mounted and 

all conditions must be fulfilled to ensure fault-

free operation of the electric tool.

–

Damaged protective devices and parts must be 

properly repaired or replaced by a recognised 

workshop, insofar as nothing different is speci

-

fied in the operating manual.

–

Damaged switches must be replaced at a cus-

tomer service workshop.

–

Do not use any faulty or damaged connection 

cables.

–

Do not use any electric tool on which the switch 

cannot be switched on and off.

15 

Have  your  electric  tool  repaired  by  a  qualified 

electrician

–

This electric tool conforms to the applicable 

safety regulations. Repairs may only be per-

formed by an electrician using original spare 

parts. Otherwise accidents can occur.

16  Important!

–

For your own safety you must only use the ac-

cessories and additional units listed in the oper-

ating instructions or recommended or specified 

by the manufacturer. The use of mounted tools 

or accessories other than those recommended 

in the operating instructions or catalog may 

place your personal safety at risk.

17  Noise

–

Wear ear muffs when you use the compressor.

18  Replacing the power cable

–

To prevent hazards, leave the replacement of 

damaged power cables strictly to the manufac-

turer or a qualified electrician. There is a risk 

of electric shock!

19 

Inflating tires

–

Directly after inflating tires, check the pressure 

with a suitable pressure gauge, for example at 

your filling station.

20  Roadworthy compressors for building site opera-

tions

–

Make sure that all lines and fittings are suitable 

for the maximum permissible operating pres-

sure of the compressor.

21  Place of installation

–

Set up the compressor on an even surface.

22  It is recommended to equip the feed hoses with 

a safety cable in case of pressure above 7 bar, 

e.g. using a wire cable.

23  Avoid over-stressing the piping system by using 

flexible hose connections to prevent kinking.

24  Use a residual current circuit breaker with a trig-

ger current of 30 mA or less. Using a residual 

current circuit breaker reduces the risk of an 

electric shock.