Scheppach 59112279942, Translation Of Original Instruction Manual



 www.scheppach.com

GB | 27 

13. Mulching:

If the grass box (16) is attached, remove it and 
replace it with the mulch insert (19) as shown in 
Fig. 10-12.

m

 CAUTION!

The side discharge adaptor must not be installed
when mulching.

Setting the cutting height

m

 CAUTION!

Adjust the cutting height only when the engine is 

switched off and the plug boot has been pulled.

•  Before you begin to mow, check to ensure that the 

blade is not blunt and that none of the fasteners are 
damaged.

•  To prevent any imbalance, replace blunt and/or 

damaged blades as a set only (if applicable). To 

carry out this check, first switch off the engine and 

pull the spark plug boot.

•  The cutting height is centrally adjusted with the cut-

ting height adjustor lever (Fig.13/ Item 14). 7 differ-
ent cutting heights can be selected.

•  Pull the adjustor lever out and select the desired 

cutting height. The lever snaps into the desired po-
sition. (Fig. 13)

Preparing the area to be mowed

Before mowing, carefully examine the area. Remove 
stones, sticks, bones, wires, toys and other objects 
that may be ejected.

9.  Operation

m

 CAUTION!

The engine does not come with oil in it. There-

fore, ensure that you add 0,5 litres of oil before 

starting it up. Use normal, multigrade oil (SAE30). 

The oil level in the engine must be checked each 

time before mowing.

You will also need to fill in petrol, as this is also 

not supplied upon delivery.

•  In order to avoid any unintentional start-ups of the 

lawn mower, it comes equipped with an engine 
brake (Fig. 1/ Item 3) which must be pulled back 
before the engine can be started. When the engine 
control lever is released it must return to its initial 
position, at which point the engine automatically 
switches off.

•  Press the engine brake lever (3) together and give 

the starter cord (17) a vigorous pull. (Fig. 14)
Attention: When you pull the starting rope the cut-
ting blade rotates even when dissolved motor brake 
lever. Make sure that there are no body parts in 
danger zone of cutting blade.

•  When the engine is running, press the drive lever 

(2) to the handle (1) in order to engage drive on the 
mower.

8.  Before starting the equipment

Assembling the components

Some parts of the mower come disassembled. For 
quick and easy assembly, read and follow the instruc-
tions below.

Important! You will need the following additional tools 
(not supplied) for assembly, and also for maintenance 
work:
•  Oil drip pan (for oil change)
•  A 1 litre measuring jug (oil/petrol resistant)
• 

A petrol can (5 litres is sufficient for approx. 6 op

-

erating hours)

• 

A funnel (suitable for the tankʼs petrol filler neck)

•  Household wipes (to wipe up oil/petrol residue; dis-

pose of these at a filling station)

•  A petrol suction pump (plastic, available from DIY 

stores)

•  An oil can with hand pump (available from DIY 

stores)

•  0,5 litre of engine oil (SAE 30)

Assembly

1.  Take the mower and attachment parts out of the 

packaging and check that all parts are present.

2.  Attach the lower push bar (4a) to both sides of the 

mower with one screw (a), 1 washer (c), 1 plastic 
star grip nut (d) each. Make sure that the cables, 
which will be attached later, are not in the way (Fig. 
2-3).

3.  Attach the upper push bar (4) on the lower push 

bar with one quick-release lever (5), one wash-
er big (b), one washer small (c) and one plas-
tic star grip nut (d) each on both sides (Fig. 4-5). 
Note the correct alignment of the quick-release le-

ver fixation slice ensuring the quick-release function 

remains intact.

4.  Guide the gas throttle through the cup holder (22) 

unit as shown in figure 5a.

5.  Insert the throttle cable into the engine brake le-

ver (3) using a plier. (fig. 5b-5c)

6.  Fit speed lever (21) and tighten with screw (g). Fig. 

5d - 5e

7.  Secure the cup holder unit (22) using the screws 

(f) on the upper push bar (4). (fig. 5d)

8.  Insert the pull start handle (17) in the designated 

hook as shown in Fig. 6.

9.  Fix the cables to the push bar with the cable clips 

(18) provided (Fig. 7).

10. Grass box (16) - open it up and click the plastic 

clips into position on the frame (Fig. 8).

11. Mowing with grass box:

Lift  the  discharge  flap  (15)  with  one  hand  and 

hang the grass box (16) as shown in Fig. 9.

12. Mowing with side discharge (8):

Lift the side discharge flap and mount the side 

discharge adaptor (Fig. 15/15a). If the grass box 
is attached, remove it and replace it with the 
mulch insert.