www.scheppach.com
service@scheppach.com
+(49)-08223-4002-99
+(49)-08223-4002-58
10 І 68
NOTE
For an accurate estimate of the noise emission load
during a certain working period, the times during which
the appliance is switched off or is running but not actu
-
ally being used must also be taken into consideration.
This can significantly reduce the noise emission load
over the total working period.
General safety instructions for com-
pressed air tools
WARNING!
For multiple hazards: Please ensure that
you have read and understood the safety instructions
before adjusting, operating, repairing, maintaining or
replacement of accessories on the sander or polisher
as well as before working in the vicinity of the machi
-
ne. Failure to do this can result in serious bodily injury.
•
The sander or polisher should only be adjusted, set
or used by adequately qualified and trained opera
-
tors.
•
This sander or polisher may not be modified. Modi
-
fications can reduce the effectiveness of the safety
measures and increase the risks for the operator.
•
Do not use a sander or polisher if the tool has been
damaged.
•
The appliance must be inspected regularly to ensure
that it is labelled with the required rated values and
markings given in this manual. The user must con
-
tact the manufacturer to obtain replacement labels if
necessary.
Save all warnings and safety instructions for fu-
ture reference. The safety instructions should not
be lost – give them to the operator.
Hazards caused by flying parts
•
If a workpiece or accessory or even part of the ma
-
chine tool itself breaks, parts can be flung out at
high speeds.
•
When operating the sander or polisher or when ex
-
changing accessories on the appliance, always wear
eye protection. The degree of necessary protection
must be evaluated separately for each individual
task.
•
Wear a safety helmet if working above head height.
In this case, the risks for others should also be as
-
sessed.
•
You must ensure that the workpiece has been secu
-
rely fixed.
•
Ensure that the sparks generated during use cannot
cause any hazards.
•
Disconnect the grinder from the power supply before
replacing the grinding material and before carrying
out maintenance work.
•
In this case, the risks for others should also be as
-
sessed.
Hazards caused by entanglement
•
Suffocation, scalping or and/or cut wounds can oc
-
cur if loose clothing, jewellery, necklaces, hair or
gloves are not kept away from the machine and its
accessories.
Hazards during operation
•
When using the machine, the operator‘s hands can
be subject to hazards such as cuts, grazing and
heat. Wear suitable gloves to protect your hands.
•
The operator and maintenance personnel must be
physically capable of handling the size, mass and
power of the machine.
•
Hold the machine correctly: be ready to counter
-
act any normal or sudden movements - have both
hands ready.
Introduction
MANUFACTURER:
scheppach
Fabrikation von Holzbearbeitungsmaschine GmbH
Günzburger Straße 69
D-89335 Ichenhausen
DEAR CUSTOMER,
We hope your new tool brings you much enjoyment and
success.
NOTE:
According to the applicable product liability laws, the
manufacturer of the device does not assume liability
for damages to the product or damages caused by the
product that occurs due to:
•
Improper handling,
•
Non-compliance of the operating instructions,
•
Repairs by third parties, not by authorized service
technicians,
• Installation and replacement of non-original spare
parts,
•
Application other than specified,
Intended use
This compressed air-powered random orbital sander is
suitable for sanding, polishing and for the preparation
of various surfaces. Any other usage of or modification
to the appliance is deemed to be improper and car
-
ries a significant risk of accidents. The manufacturer
accepts no responsibility for damage(s) resulting from
improper usage. This appliance in intended only for
domestic use.
Features
1. Housing
2. Blocking device
3. Trigger
4. Handle
5. Connector nipple
6. Speed controller
7. Spindle lock
8. Eccentric spindle with grinding disc socket
9. Grinding disc
10. Protective cuff
11. Sandpaper disc
12. Oil container
Technical data
Rotational speed
10000 min
-1
Rated air pressure
max. 6.3 bar
Airflow
93.4 l/min
Grinding disc
ø 150 mm
Sound pressure level
89.3 dB(A)
Sound power level
100.3 dB(A)
Uncertainty K
3 dB
WARNING!
The noise emission levels specified in these instruc
-
tions have been measured in accordance with the
standardised measuring procedure specified in ISO
15744 and can be used to make equipment compari
-
sons. The noise emission values vary in accordance
with the use of the compressed air tool and may be
higher than the values specified in these instruction
in some cases. It is easy to underestimate the noise
emission load if the compressed air tool is used regu
-
larly in a certain manner.
