Scheppach BC52PB, Translation From The Original Instruction Manual

26

GB

7. Before starting the equipment

Each time before use, check the following: 

• 

That there are no leaks in the fuel system.

• 

That the equipment is in perfect condition and that 
the safety devices and cutting devices are complete.

• 

That all screws are securely fastened.

• 

That all moving parts move smoothly.

1 

Fuel and oil

Recommended fuels
Use only a mixture of unleaded petrol and special 
2-stroke engine oil. Mix the fuel mixture as indicated in 
the fuel mixing table.

Important: Do not use a fuel mixture which has been 
stored for longer than 90 days.
Important: Never use 2-stroke oil with a recommended 
mixing ratio of 100:1. The manufacturer’s warranty
will be voided in case of engine damage due to inade-
quate lubrication.
Important: Only use containers designed and appro-
ved for the purpose to transport and store fuel.

Pour the correct quantities of petrol and 2-stroke oil 
into the mixing bottle (see scale printed on the bottle). 
Then shake the bottle well.

Never use oil for 4-cycle engine or use water cooled 
2-cycle engine. It can cause spark plug fouling exhaust 
part blocking or piston ring sticking.
Mixed fuels, which have been left unused for a period 
of one month or more, may clog the carburetor or result 
in the engine foiling to operate property. Put remained 
fuel into an airtight container and keep it in the dark and 
cool room.

2 

Fuel mixing table

Mixing procedure: 40 parts petrol to 1 part oil
Example:
1 l   Petrol   :   0,025 l   2-stroke oil
5 l   Petrol   :   0,125 l   2-stroke oil

Warning!
Take care of the emission of exhaust gases.
Always shut off engine before fueling. Never add fuel 
to a machine with a running or hot engine. Take care 

of fire!

8. Attachment and operation

ASSEMBLY

When assembling this machine, please follow the inst-
ructions for assembly printed.

1 

 Assemble the handle on the machine. Fig. 4 -6

• 

Assemble the bike type handle on the machine: First 
release the inner hex screws, second take right and 
left handle on the centre of handle holder.

• 

Last assemble the handle holder and tighten the in-
ner screws enough.

2. 

Mounting the shaft. Fig. 7

• 

Push the lower part of the shaft (b) right down until 
the stop pin (a) slots into the hole (c) in the shaft. 
This is easier to do if you rotate the bottom of the 
shaft (b) slightly in both directions. The pin (a) is in 
place when it is completely lodged in the hole.

• 

Lastly, tighten the knob (d) securely.

3. 

Assemble the safe guard. Fig. 11 13

• 

Fix the safe guard with hex key and wrench enc-
losed as stardard accessories for tighting the nuts 
enough. Please see the below pictures showing.

m 

Warning! 

Use only original manufacturer‘s repla-

cement parts, accessories and attachments. Failure 
to do so can cause poor performance, possible injury 
and may void your warranty. Never use the machine 
without the guard assembled!

4. 

 Assemble and disassemble the cutting head
grass trimmer / nylon cutting head. Fig. 14 - 15

• 

Release the nut.

Line up the two holes of flange and shield, use one 
screw driver to hold the flange as below and turn the 

socket wrench clockwise, the nut will be released.

• 

Fit the Nylon cutting head. 
Remove another shield after release the nut. Still hold 

the flange, take the Nylon cutting head on the shaft 

and rotate counter-clockwise, the Nylon cutting head 

is fitted. Fig. 15

• 

Release the Nylon cutting head. Fig. 10

Use screw driver to hold flange and then rotate the 

Nylon cutting head clockwise, it will be replaced.

Brush cutter / Cutter blade

• 

Fit the blade. Fig. 8 - 10

Take the outer flange off after release the nut, then 
put the blade (4), outer flange (24), shield (23) and 

nut according to priority as below picture. Note the 
blade rotation direction needs be same as below 

picture. Use screw driver to hold flange and tighten 

nut counter-clockwise, ensure the nut is tightened 
enough.

• 

Release blade. Use screw driver to hold flange and 

release nut, the blade can be took off.

m 

Warning!

Please make sure the cutting head has been assem-
bled correctly before use!

Saw blade

m 

Warning!

For saw blade use and installation use only the desig-
nated protection.

• 

Assemble the saw blade guard. Fig. 44

• 

Fix the saw blade guard with hex key and wrench 
enclosed as stardard accessories for tighting the 
nuts enough.

m 

Warning! 

Use only original manufacturer‘s repla-

cement parts, accessories and attachments. Failure 
to do so can cause poor performance, possible injury 
and may void your warranty. Never use the machine 
without the guard assembled!