Scheppach HC51V, Translation From The Original Instruction Manual

14

GB

We accept no liability for damage or accidents which 

arise due to non-observance of these instructions 

and the safety information.

2.  Layout (Fig. 1,2)

1. 

Drain plug for condensation water

2. 

Pressure vessel

3. 

Wheel

4. 

Supporting foot

5. 

Quick-lock coupling (regulated compressed air)

6. 

Pressure gauge (for reading the preset vessel  

pressure)

7. 

Pressure regulator

8. 

ON/OFF switch

9. 

Transport handle

10. Safety valve

A  Hex bolt

B  Nut

C  Washer

D  Flange nut

3.  Scope of delivery

• 

Open the packaging and remove the device care-

fully.

• 

Remove the packaging material as well as the 

pack aging and transport bracing (if available).

• 

Check that the delivery is complete.

• 

Check the device and accessory parts for trans-

port damage.

• 

If possible, store the packaging until the warranty 

period has expired.

ATTENTION

The device and packaging materials are not toys!

Children must not be allowed to play with plastic 

bags, film and small parts! There is a risk of swal

-

lowing and 

suffocation!

4.  Proper use

The compressor is designed to generate com-

pressed air for compressed-air driven tools which 

can be driven with an air volume of up to approx. 

170 l/min (e.g. tire inflator, blow-out pistol and paint 

spray gun). Due to the limited air output it is not pos-

sible to use the compressor to drive tools with very 

high air consumption (for example orbital sanders, 

rod grinders and hammer screwdrivers).

The equipment is to be used only for its prescribed 

purpose. Any other use is deemed to be a case of 

misuse. The user / operator and not the manufac-

turer will be liable for any damage or injuries of any 

kind caused as a result of this.

1.  Introduction

MANUFACTURER:

scheppach

Fabrikation von Holzbearbeitungsmaschine GmbH

Günzburger Straße 69

D-89335 Ichenhausen

DEAR CUSTOMER,

We hope your new tool brings you much enjoyment 

and success.

NOTE:

According to the applicable product liability laws, the 

manufacturer of the device does not assume liability 

for damages to the product or damages caused by 

the  product that occurs due to:

•  Improper handling,

•  Non-compliance of the operating instructions,

•  Repairs by third parties, not by authorized service 

technicians,

•  Installation and replacement of non-original spare 

parts,

• 

Application other than specified,

•  A breakdown of the electrical system that occurs 

due to the non-compliance of the electric regu-

lations and VDE regulations 0100, DIN 57113 / 

VDE0113.

WE RECOMMEND:

Read through the complete text in the operating in-

structions before installing and commissioning the 

device. The operating instructions are intended to 

help the user to become familiar with the machine 

and take advantage of its application possibilities in 

accordance with the recommendations. The operat-

ing instructions contain important information on how 

to operate the machine safely, professionally and 

economically, how to avoid danger, costly repairs, re-

duce downtimes and how to increase reliability and 

service life of the machine.

In addition to the safety regulations in the operating 

instructions, you have to meet the applicable regula-

tions that apply for the operation of the machine in 

your country. Keep the operating instructions pack-

age with the machine at all times and store it in a 

plastic cover to protect it from dirt and moisture. 

Read the instruction manual each time before op-

erating the machine and carefully follow its informa-

tion. The machine can only be operated by persons 

who were instructed concerning the operation of the 

machine and who are informed about the associated 

dangers. The minimum age requirement must be 

complied with.

In addition to the safety instructions contained in this 

operating manual and the specific regulations of your 

country, the technical rules generally accepted for the 

operation of machines of the same type must be ob-

served.