www.scheppach.com
service@scheppach.com
+(49)-08223-4002-99
+(49)-08223-4002-58
14 І 112
Device description (Fig. 1-8)
1. Transport handle
2. Pressure switch
3.
Pressure regulator
4. Quick-lock coupling (regulated compressed air)
5. Pressure gauge (for reading the preset vessel
pressure)
6. Pressure gauge (for reading the vessel pressure)
7. Pressure vessel
8. Supporting foot
9.
Wheel hub bolt
10.
Wheel
11. Pressure pipe
12. Crankcase
13. Oil plug
14. Air filter
15. Drain plug for condensation water
16. Safety valve
17. ON/OFF switch
18. Oil level / -control display
19. Oil drain plug / screw
20. Overload / protection switch
Scope of delivery
•
Open the packaging and remove the device carefully.
•
Remove the packaging material as well as the pack-
aging and transport bracing (if available).
•
Check that the delivery is complete.
•
Check the device and accessory parts for transport
damage.
•
If possible, store the packaging until the warranty pe-
riod has expired.
m
ATTENTION!
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, film and small parts! There is a risk of swal
-
lowing and suffocation!
Intended use
The compressor is designed to generate compressed
air for compressed-air driven tools which can be driven
with an air volume of up to approx. 200 l/min
(e.g. tire
infl ator, blow-out pistol and paint spray gun).
Due to the limited air output it is not possible to use the
compressor to drive tools with very high air consump-
tion (for example orbital sanders, rod grinders and ham-
mer screwdrivers).
The equipment is to be used only for its prescribed pur-
pose. Any other use is deemed to be a case of misuse.
The user / operator and not the manufacturer will be li-
able for any damage or injuries of any kind caused as
a result of this.
Please note that our equipment has not been designed
for use in commercial, trade or industrial applications.
Our warranty will be voided if the equipment is used in
commercial, trade or industrial businesses or for equiv-
alent purposes.
Introduction
MANUFACTURER:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
DEAR CUSTOMER,
we hope your new tool brings you much enjoyment and
success.
NOTE:
According to the applicable product liability laws, the
manufacturer of the device does not assume liability
for damages to the product or damages caused by the
product that occurs due to:
•
Improper handling,
•
Non-compliance of the operating instructions,
•
Repairs by third parties, not by authorized service
technicians,
•
Installation and replacement of non-original spare
parts,
•
Application other than specified,
•
A breakdown of the electrical system that occurs due
to the non-compliance of the electric regulations and
VDE regulations 0100, DIN 57113 / VDE0113.
WE RECOMMEND:
Read through the complete text in the operating instruc-
tions before installing and commissioning the device.
The operating instructions are intended to help the user
to become familiar with the machine and take advantage
of its application possibilities in accordance with the
recommendations. The operating instructions contain
important information on how to operate the machine
safely, professionally and economically, how to avoid
danger, costly repairs, reduce downtimes and how to in-
crease reliability and service life of the machine.
In addition to the safety regulations in the operating
instructions, you have to meet the applicable regula-
tions that apply for the operation of the machine in your
country. Keep the operating instructions package with
the machine at all times and store it in a plastic cover
to protect it from dirt and moisture. Read the instruction
manual each time before operating the machine and
carefully follow its information. The machine can only
be operated by persons who were instructed concern-
ing the operation of the machine and who are informed
about the associated dangers. The minimum age re-
quirement must be complied with.
In addition to the safety notices contained in this op-
erating manual and the particular instructions for your
country, the generally recognised technical regulations
for the operation of identical devices must be complied
with.
