www.scheppach.com /
service@scheppach.com /
+(49)-08223-4002-99 /
+(49)-08223-4002-58
GB | 19
We accept no liability for accidents or damage that
occur due to a failure to observe this manual and the
safety instructions.
2.
Device description
1.
Fixed protective guard (small)
2. Handle
3. Movable protective guard
4.
Fixed protective guard (large)
5. Tray table for split logs
6. Foot
7. Transport handle
8.
Star grip screws (4x)
9. Cross bar
10. Transport wheels
11. Wheel axle
12.
Struts (2x)
13. Engine
14. On/off switch
15. Control lever
16. Safety switch
17. Bleeder screw
18. Oil drain screw with dipstick
3.
Scope of delivery
A. Operating manual
B. Enclosed accessories bag
C.
Handle (2x)
D. Log splitter
E.
Protective guard fixed (small)
F. Protective guard movable
G.
Protective guard fixed (large)
H. Tray table
I. Transport wheels
J. Complete base frame
4. Intended use
The equipment is to be used only for its prescribed
purpose. Any other use is deemed to be a case of
misuse. The user / operator and not the manufactur
-
er will be liable for any damage or injuries of any kind
caused as a result of this.
To use the equipment properly you must also observe
the safety information, the assembly instructions and
the operating instructions to be found in this manual.
All persons who use and service the equipment have
to be acquainted with this manual and must be in
-
formed about the equipment’s potential hazards.
It is also imperative to observe the accident preven
-
tion regulations in force in your area. The same ap
-
plies for the general rules of health and safety at
work.
The manufacturer will not be liable for any changes
made to the equipment nor for any damage resulting
from such changes.
1. Introduction
MANUFACTURER:
scheppach
Fabrikation von Holzbearbeitungsmaschine GmbH
Günzburger Straße 69
D-89335 Ichenhausen
DEAR CUSTOMER,
We hope your new tool brings you much enjoyment
and success.
NOTE:
According to the applicable product liability laws, the
manufacturer of the device does not assume liability
for damages to the product or damages caused by
the product that occurs due to:
• Improper handling,
•
Non-compliance of the operating instructions,
• Repairs by third parties, not by authorized service
technicians,
•
Installation and replacement of non-original spare
parts,
•
Application other than specified,
• A breakdown of the electrical system that occurs
due to the non-compliance of the electric regu-
lations and VDE regulations 0100, DIN 57113 /
VDE0113.
We recommend:
Read through the complete text in the operating in
-
structions before installing and commissioning the
device. The operating instructions are intended to
help the user to become familiar with the machine
and take advantage of its application possibilities in
accordance with the recommendations. The operat
-
ing instructions contain important information on how
to operate the machine safely, professionally and
economically, how to avoid danger, costly repairs, re
-
duce downtimes and how to increase reliability and
service life of the machine.
In addition to the safety regulations in the operating
instructions, you have to meet the applicable regu
-
lations that apply for the operation of the machine in
your country. Keep the operating instructions pack
-
age with the machine at all times and store it in a
plastic cover to protect it from dirt and moisture.
Read the instruction manual each time before op
-
erating the machine and carefully follow its informa
-
tion. The machine can only be operated by persons
who were instructed concerning the operation of the
machine and who are informed about the associat
-
ed dangers. The minimum age requirement must be
complied with.
In addition to the safety instructions in this operating
manual and the separate regulations of your country,
the generally recognised technical rules for operat
-
ing woodworking machines must also be observed.
