Scheppach Precisa 4.0 Series Operating Instructions Manual Download

Page: 24 / 96

16 english

Fig.“J“
• Slot the threaded sections into the guide tube and bolt
to the two supports
3 cheese-head screws

M 8 x 16

3 washers

ø 8

• Lightly tighten the cheese-head screws M 8 x 16.
• Adjust the guide tube to be parallel to the bench top

checking dimensions=55 mm

•

The guide tube must end exactly flush with the left-

hand edge of the bench top
• Tighten cheesehead screws M 8 x 16, M 8 x 20.
• Pull up (open) the eccentric lever on the guide slide
and fit the guide slide onto the guide tube trom above.

Adjusting the longitudinal fence
Fig.“K“
To accurately adjust the longitudinal fence to the saw bla-
de,

loosen the tour cheese-head screws (1) and clamp the

guide slide in a position about

100 mm from the saw

blade. Place a straightedge, about

600 mm long, against

the saw blade and adjust the fence until it is parallel, by
repeatedly measuring

(X) and readjusting. Tighten the

cheesehead screws

(1) once more.

Important!
For cutting widths under 120 mm, always use a push
stick.

Stop rail
Position 1 =
for working on raised surfaces.

The cutting width indicated on the scale matches the
actual cutting width.

Position 2 =
for working on low surfaces.

The actual cutting width differs fram the scale reading by
minus 32 mm.

Example:
Actual cutting width 68 mm Scale reads 100 mm

Attaching the push stick
Fig.“K1“
Mount 2 holding clamps on the longitudinal fence.
1 flat raund screw

B 4.2 x 9.5 each

Insert the push stick into the holding clamps.

Adjusting the reading glass
Fig.“L“
Position the stop fence against the saw blade and tighten
the eccentric lever. Loosen the screws on the reading
glass and set the

division mark exactly over the zero mark

on the scale.

Tighten the screws.

Mounting of precision adjustment (special accessories)
Fig. „L1“
Precision adjustment is carried out by
means of the adjustment spindie

(3)

with the cam lever locked

(1) and cam

lever unlocked

(2).

If SPECIAL ACCESSORIES are used, they must be mounted in
the following order before the bench extension.
1. Bench extension - broadening
2. Bench extension bracket (basic equipement)
3. Saw blade protection - suction attachment
4. Bench extension -Iength (basic equipment)
5.Slide

Skip SPECIAL ACCESSORIES, if not installed, when observing
the order of mounting.

Cross cut gauge
Fig.“M“
Screw together the cross cut gauge.
2 flat round screws

M6 x 25

2wingnuts

washer

A 6,4

1 clamping lever

M6 x 20

1 knob pin

Fig.“M1“
Depending on your preference, insert the cross cut gauge
into the guide groove either on the left or right ofthe saw
blade. Pull the mounted clamping lever in the
direction of the arrow and swing to the rear.

Lock the cross cut gauge at zero degrees with the knob
pin.

The zero mark on the scale must be in line with the scale
pointer. If it is not, loosen the four cross head screws on
the scale and adjust accordingly.

When working, bring the stop rail as close up to the saw
blade as possible.

Setting up and adjusting
Make sure your scheppach

ill Precisa 4.0 bench circular saw is

standing horizontally and is steady.

Compensate any unevenness on the floor.

90°/45° Saw blade - fine adjustment
Fig.“M2“
• Before starting up, check the 90°/45° saw blade posit
ion, and if necessariy, carry out the fine adjustment.
• There are two hexagon screws forfine adjustment, on
the adjustment segment, which is located on the back
wall of the cirular-saw bench.
• After each fine adjustment, tighten the check nuts
firmly
• To exactly determine the angle, ALWAYS carry out a test
cut.