background image

6  •  Schlage  •  CO-250 user guide

Test lock operation

If you encounter problems while performing any of the following tests, review the installation 

guide and correct any problems.

Mechanical test

1.  Rotate the inside lever or depress the push bar to open the door. Operation should be 

smooth, and the latch should retract.

2.  Insert the key into the keyway and rotate the key and the outside lever to open the door. 

Operation should be smooth, and the latch should retract. The Schlage button will light 

solid green until the key is released and the latch is extended.

Test in factory default mode

1.  For locks with a keypad, press any number key. The lock will beep and the Schlage 

button will blink red.

2.  The Schlage button will blink red twice when a credential is presented and the lock is in 

factory default mode, and has no access programming.

3.  For locks with keypads, enter the default PIN (13579 and “#”) to verify access. The 

Schlage button will blink green, a beep will sound, and the door will unlock for the preset 

relock delay period. After the relock delay period, the lock will relock and the Schlage 

button will blink red. If the lever retracts and holds the latch through the relock delay 

period, then the Schlage button will light green until the lever is released.

Test in normal operation mode

1.  Present a valid credential. The Schlage button will blink green, a beep will sound and 

the door will unlock for the preset lock delay period. The lock will re-lock after the relock 

delay period and the Schlage button will then blink red. If the lever retracts and holds the 

latch through the relock delay period, then the Schlage button will light green until the 

lever is released.

2.  If an invalid credential is presented, the Schlage button will blink red, a beep will sound 

and the door will not unlock.

Normal lock operation

After the lock has been programmed, present credentials to operate the lock as follows:

Credential type

Action

Credential

Present credential to reader 

Green blink and access granted

+ PIN credential

P PIN credential to reader 

Green blink and access granted

1  If the PIN is entered incorrectly, press “

*

” to start over.

Summary of Contents for CO-250













Reviews: