background image

Reset to factory defaults

All information in the lock will be deleted and reset to factory defaults!
The door must be locked (not toggled open or in the middle of normal access) before 

resetting to factory defaults.

Level 1 factory default reset

 

L

Level 1 factory default reset will delete configurations and settings in the main 

controller in the lock.

 

L

Main controller configurations that will reset to factory default include: 

programming and user codes.

 

L

Level 1 factory default reset will not reset configurations and settings in the 

reader.

1.  Press and hold the Schlage button. Wait for the lock to beep twice and two green blinks 

of the Schlage button, indicating confirmation.

2.  After confirmation signals, release the Schlage button.

3.  Rotate the mechanical key within 10 seconds and hold. The Schlage button will 

light green. Continue holding the key until confirmation signals are observed (the 

Schlage button light will turn off one second and a one second beep will sound). After 

confirmation signals, release the mechanical key.

4.  The Schlage button will light green for one second and a one-second beep will sound to 

confirm reset to factory defaults.

 

L

If the mechanical key is not rotated within 10 seconds, two beeps and two red 

blinks indicate timeout.

Level 2 factory default reset

 

L

Level 2 factory default reset will delete all configurations and settings in the lock 

and the reader.

 

L

Reader configurations that will reset to factory default include: keypad format, 

magstripe reader track, beeper on/off, and contactless card.

 

L

Days in Use counter and lock type configurations will not reset.

To complete level 2 factory default reset, repeat steps 2 through 4 

within 10 seconds of the 

confirmation signals of level 1 factory default reset.

If more than 10 seconds pass after the confirmation signals of level 1 reset, then level 1 reset 

must be repeated prior to performing level 2 reset.

Summary of Contents for CO-250













Reviews: