SED100 Electronic Touchscreen Deadbolt
USER GUIDE
1
Overview
Key Override
Red indicator
Low Battery Indicator
Green Indicator
Lock Button
Clear Button
Touch Screen
1
1
2
3
6
7
4
5
RED INDICATOR
1
LOCK / UNLOCK
2
Locking, Unlocking and Programming
4
PROGRAMMING
- Touch to activate or lock.
- Unlocks by entering a valid user code.
- Programs by entering a valid programming code.
- Press button to cancel or exit programming mode.
2
LOW BATTERY INDICATOR
Press button to cancel any typo or exit programming mode.
Represents a correct entry or positive response by flashing green light.
Flashes when the batteries are low in power.
Represents an incorrect entry or caution by flashing red light.
5
CLEAR BUTTON
- Locks when pressed.
- Represents “enter” when in programming mode.
6
LOCK BUTTON
Used to unlock with a key when there is a code or battery failure.
7
MECHANICAL KEYWAY OVERRIDE
Protects the batteries.
8
BATTERY COVER
Locks or unlocks manually.
- Press set button for 3 seconds then enter correct programming code to start programming.
- Please refer to for more information about programming mode.
SET BUTTON
2
4
-
9
INTERIOR THUMBTURN
C
C
3
GREEN INDICATOR
4
TOUCH SCREEN
Operation
Step 2
Step 1
Step 3
Step 4
To unlock
Touch
the
screen.
Enter valid user
code or
programming
code.
Press four random
scramble digits lit on the
screen.
Note:
Only if scramble
code is enabled
(see - - 22).
To lock
To unlock
1
2
3
4
5
6
7
8
9
c
0
→
→
Correct
Incorrect
1
2
3
4
5
6
7
8
9
c
0
→
To lock
→
→
Touch screen is
temporarily disabled
for 60 seconds after 4
consecutive incorrect
attempts.
2
2
Note
Function
Change the existing programming
code
A programming code can be used to program or
unlock.
Function Code
10
Add a user code(s)
A user code (pin number) is set up by the
programming code and can be used to unlock.
20
Delete all user codes
Deletes all user codes.
40
Add single-entry code(s)
A single-use user code is set up by the program-
ming code and can only be used *once* to
unlock.
21
Delete individual user code(s)
Deletes individual user code(s).
30
Keypad scrambling code
The scrambling code is a set of random digits to
be entered prior to any user code or single-entry
code, preventing code probing.
22
Volume control
Incrementally increases volume from mute to
loud.
Set up auto-lock time delay (10-99 seconds).
Locks automatically in 10-99 seconds if enabled.
60
Auto-lock delay timer
70
Auto-lock function
80
Vacation mode
Temporarily disable all active user codes until
unit is re-enabled.
50
3
ACCESS CODE
2
FUNCTION CODES
Code Length
Code Capacity
Remark
4 - 8 digits
1 set
4 - 8 digits
25 sets
4 digits
4 sets
1. A programming code can be used to program or
unlock.
2. The default programming code is “12345678”.
Programming
Code:
User Code:
Single-entry
Code:
A user code is set up by the programming code
and can be used to unlock.
A single entry code is set up by the programming
code and can only be used *once* to unlock.
21
30
50
70
10
20
22
40
60
80
Function Code
Press [SET] for
3 seconds.
Enter preset
programming code
(12345678) or
current
programming code
if it has been
changed.
0
＋
＋
1
0
＋
＋
2
New
Programming
Code
(4-8 digits)
New
Programming
Code
(4-8 digits)
New User Code
(4-8 digits)
New User Code
(4-8 digits)
Single-use User
Code (4 digits)
Single-use User
Code (4 digits)
0
＋
＋
3
1
＋
＋
2
User Code
(4-8 digits)
Enter new
amount (10-99)
User Code
(4-8 digits)
Delete all user
codes
2
＋
＋
2
0
＋
0
＋
＋
4
C
0
＋
＋
7
0
＋
＋
8
1
＋
Turn On
Turn Off
0
＋
1
＋
Turn On
Turn Off
0
＋
＋
6
0
＋
＋
1
＋
Mute
1 (softer)
2
＋
2 (normal)
3
＋
3 (louder)
0
＋
＋
5
0
＋
1
＋
Turn On
New amount
Turn Off
1
2
3
4
5
6
7
8
9
c
0
Step 1
Step 2
Step 3
Step 4
Change the
existing
programming
code
Add a user
code(s)
Add single-entry
code(s)
Keypad scramble
code
Delete individual
user code(s)
Delete all user
codes
Vacation mode
Volume control
Auto-lock delay
timer
Auto-lock function
The lockset will exit the programming mode and resume to the stand-by status if no input is made in 10 seconds.
Interior Thumbturn
8
Battery Cover
9
Set Button
10
10
