Schlage VIP 5500 Series Installation Manual Download | Manualshive

Page: 7 / 9

background image

Form 57033 Rev. A

01-05-2004

7

VIP 5500 OPEN ARCHITECTURE MORTISE LOCK

INSTALLATION MANUAL

7. INSTALL OUTSIDE SPINDLE, OUTSIDE ESCUTCHEON AND BASE PLATE ASSEMBLY:

Install outside escutcheon and spindle then install base plate assembly onto inside of door. Use socket cap screws with
washers on top standoffs and phillips head screws on lower standoffs. Note that the cam on the outside escutcheon must
be positioned with the dot at the 6 o’Clock position and outside spindle must be inserted as shown in details.
NOTE: Battery Powered inside baseplate shown.

OUTSIDE SPINDLE MUST BE
INSERTED AS SHOWN

SOCKET CAP
SCREW

,

WASHERS

5/32” HEX
WRENCH

BASE PLATE ASSEMBLY

PASS WIRING HARNESS THROUGH

1”

HOLE IN DOOR

PHILLIPS HEAD
SCREWS

DOT

-

FACES

DOWN

OUTSIDE
SPINDLE
POSITION

CAM

DETAIL

IMPORTANT!
DO NOT OVERTIGHTEN
FASTENERS OR DOOR
WILL COMPRESS.

«
...
5
6
7
8
9
»

Summary of Contents for VIP 5500 Series










Reviews:

No comments

Related manuals for VIP 5500 Series

Brand: Kaba Pages: 128

Brand: Kaba Mas Pages: 20

Saflok InSync I

Brand: Kaba Group Pages: 2

Brand: QC Supply Pages: 3

Brand: PBB Pages: 2

Brand: Burg Wächter Pages: 11

Brand: 2gig Technologies Pages: 2

Brand: Philips Pages: 16

Brand: Schlage Pages: 16

Brand: Schlage Pages: 32

Brand: ZK Software Pages: 20

Brand: Detex Pages: 9

ADVANTEX 87 Series

Brand: Detex Pages: 20

Brand: Velleman Pages: 20

Brand: Dormakaba Pages: 12

CROMPTON Ironmongery 0060BH-305-10

Brand: ERA Pages: 2

Brand: RS PRO Pages: 8

MagnaLatch MLSPS2

Brand: D&D Technologies Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands