14. Appendix
96|108
Reference Manual |Edition 4.0 (10-2013) |EcoCut 3300
MICROLUBE GBU-Y 131
Conforms to Regulation (EC) No. 1907/2006 (REACH), Annex II - United Kingdom (UK)
SECTION 8: Exposure controls/personal protection
Hand protection
Use a properly fitted, air-purifying or air-fed respirator complying with an approved
standard if a risk assessment indicates this is necessary. Respirator selection must
be based on known or anticipated exposure levels, the hazards of the product and
the safe working limits of the selected respirator.
Chemical-resistant, impervious gloves complying with an approved standard should
be worn at all times when handling chemical products if a risk assessment indicates
this is necessary.
Safety eyewear complying with an approved standard should be used when a risk
assessment indicates this is necessary to avoid exposure to liquid splashes, mists,
gases or dusts.
Eye/face protection
Respiratory protection
:
:
:
Skin protection
Personal protective equipment for the body should be selected based on the task
being performed and the risks involved and should be approved by a specialist
before handling this product.
:
Environmental exposure
controls
:
Emissions from ventilation or work process equipment should be checked to ensure
they comply with the requirements of environmental protection legislation. In some
cases, fume scrubbers, filters or engineering modifications to the process
equipment will be necessary to reduce emissions to acceptable levels.
Appropriate engineering
controls
:
No special ventilation requirements. Good general ventilation should be sufficient to
control worker exposure to airborne contaminants. If this product contains
ingredients with exposure limits, use process enclosures, local exhaust ventilation or
other engineering controls to keep worker exposure below any recommended or
statutory limits.
Wash hands, forearms and face thoroughly after handling chemical products, before
eating, smoking and using the lavatory and at the end of the working period.
Appropriate techniques should be used to remove potentially contaminated clothing.
Wash contaminated clothing before reusing. Ensure that eyewash stations and
safety showers are close to the workstation location.
8.2 Exposure controls
Hygiene measures
:
Individual protection measures
Body protection
:
Other skin protection
Appropriate footwear and any additional skin protection measures should be
selected based on the task being performed and the risks involved and should be
approved by a specialist before handling this product.
Not available.
Melting point/freezing point
Initial boiling point and boiling
range
Vapour pressure
Solubility(ies)
Not available.
Not available.
Insoluble in the following materials: cold water.
Characteristic.
Odour
pH
Beige.
Colour
Flash point
Not applicable.
Not available.
Not available.
Not available.
Partition coefficient: n-
octanol/water
Upper/lower flammability or
explosive limits
:
:
:
:
:
:
:
:
:
:
9.1 Information on basic physical and chemical properties
Appearance
Burning time
Not applicable.
Burning rate
Not applicable.
:
:
SECTION 9: Physical and chemical properties
Flammability (solid, gas)
:
Not available.
Density
:
0.95 g/cm
3
[20°C]
Bulk Density
:
Not available.
Paste.
:
Physical state
Version
:
5/10
1
Summary of Contents for EcoCut 3300
