7
AZM201
Betriebsanleitung
Sicherheitszuhaltung
DE
Tabelle 1: Diagnoseinformationen des Sicherheitsschaltgerätes
Das Sicherheitsschaltgerät signalisiert den Betriebszustand, aber auch Störungen, über drei verschiedenfarbige LEDs am Gerät.
Systemzustand
Magnetansteuerung
IN
LED
Sicherheitsausgänge
Y1, Y2
Diagnose-
ausgang OUT
Ruhestrom Arbeitsstrom
grün
rot
gelb
AZM201Z AZM201B
-1P2PW
Tür auf
24 V (0 V)
0 V (24 V)
an
aus
aus
0 V
0 V
0 V
Tür geschlossen,
Betätiger nicht eingeführt
24 V
0 V
an
aus
aus
0 V
0 V
0 V
Tür geschlossen, Betätiger eingeführt,
nicht gesperrt
24 V
0 V
an
aus
blinkt
0 V
24 V
24 V
Tür geschlossen, Betätiger eingeführt,
Sperrung blockiert
0 V
24 V
an
aus
blinkt
0 V
24 V
0 V
Tür geschlossen,
Betätiger eingeführt und gesperrt
0 V
24 V
an
aus
an
24 V
24 V
24 V
Fehlerwarnung
1)
Zuhaltung gesperrt
0 V
24 V
an
blinkt
2)
an
24 V
1)
24 V
1)
0 V
Fehler
0 V (24 V)
24 V (0 V)
an
blinkt
2)
aus
0 V
0 V
0 V
Zusätzlich bei Ausführung I1/I2:
Betätiger Anlernen gestartet
aus
an
blinkt
0 V
0 V
0 V
Nur I2: Betätiger Anlernvorgang
(Freigabesperre)
blinkt
aus
aus
0 V
0 V
0 V
1) nach 30 min: Abschaltung wegen Fehler
2) s. Blinkcode
Tabelle 2: Fehlermeldungen / Blinkcodes rote Diagnose-LED
Blinkcodes (rot) Bezeichnung
eigenständige
Abschaltung nach
Fehlerursache
1 Blinkpuls
Fehler(-warnung) an Ausgang Y1
30 min
Fehler im Ausgangstest oder Spannung am Ausgang Y1,
obwohl der Ausgang abgeschaltet ist
2 Blinkpulse
Fehler(-warnung) an Ausgang Y2
30 min
Fehler im Ausgangstest oder Spannung am Ausgang Y2,
obwohl der Ausgang abgeschaltet ist
3 Blinkpulse
Fehler(-warnung) Querschluss
30 min
Querschluss zwischen den Ausgangsleitungen oder Fehler an
beiden Ausgängen
4 Blinkpulse
Fehler(-warnung) Übertemperatur
30 min
Temperaturmessung ergibt eine zu hohe Innentemparatur
5 Blinkpulse
Fehler Betätiger
0 min
Falscher oder defekter Betätiger
6 Blinkpulse
Fehler Betätigerkombination
0 min
Eine nicht gültige Kombination von Betätigern wurde erkannt
(Riegelbrucherkennung oder Manipulationsversuch).
Dauerrot
interner Fehler /
Fehler Über- oder Unterspannung
0 min
Gerät defekt /
Versorgungsspannung außerhalb der Spezifikationen