13
EN
CONTROLS
The control switches are located on the hood’s front panel.
To select the functions of the hood just touch the commands.
1.
ON/OFF/Stand-By key
Press shortly to set the hood to “Stand-by” (led “
b
” on), press longer (min 2
seconds) to turn off completely (
OFF –
all functions disabled except
lighting).
Press again (min 2 seconds) to re-set the hood to “Stand-by”.
2.
Light
ON/OFF key
3.
Display
4.
Speed selection key 1-2-3-1-2.........
5.
Intense speed ON/OFF key. Time - 5 minutes , the letter
P
and the residual
operation time appear in the display, the led “
a
” flashes.
After the 5 operation minutes, the hood goes back to the previously set
speed.
Press
key
1
or
5
to deactivate this function before the time.
6.
Timer ON/OFF key: it times all the speeds (led “
b
” flashing), then the hood
turns off:
1a speed: 20 minutes
2a speed: 15 minutes
3a speed: 10 minutes
The display shows the residual operation time.
Press
key
6
to deactivate this function before the time.
In case the hood or the controls do not work, it is recommended to cut off power
supply for at least 5 seconds and then turn it on again. Wait for 15 seconds and
check if the hood works properly.
Signalling of the saturation of the anti-grease filter (F) and the carbon filter
(C)
This type of hood is equipped with a device which signals when the following
maintenance operations must be carried out:
Grease filter/s – the letter
F
flashes on the display
Carbon filter – the letter
C
flashes on the display.
Signalling of the saturation of the carbon filter is normally deactivated.
To activate it, proceed as follows
Press key 1 shortly to set the hood to “Stand-by”.
Keep keys
4
and
5
pressed
contemporaneously for three seconds.
At first the letter
F
appears on the display
,
then the letter
C
appears to indicate
that the signalling of the saturation of the carbon filter is activated
Ripetere l'operazione per disattivare la segnalazione.
Saturation indicator reset
After clearing or replacing the filter, press key
1
for 3 seconds until the letter
F
(anti-grease filter/s) and/or the letter
C
stop/s flashing.
MAINTENANCE
ATTENTION!
Before performing any maintenance operation, isolate the hood
from the electrical supply by switching off at the connector and removing the
connector fuse.
Or if the appliance has been connected through a plug and socket, then the plug
must be removed from the socket.
Cleaning
The cooker hood should be cleaned regularly (at least with the same frequency
with which you carry out maintenance of the fat filters) internally and externally.
Clean using the cloth dampened with neutral liquid detergent. Do not use
abrasive products.
DO NOT USE ALCOHOL!
WARNING:
Failure to carry out the basic cleaning recommendations of the
cooker hood and replacement of the filters may cause fire risks.
Therefore, we recommend oserving these instructions.
The manufacturer declines all responsibility for any damage to the motor or any
fire damage linked to inappropriate maintenance or failure to observe the above
safety recommendations.
Maintenance of the anti-grease filters
Traps cooking grease particles.
This must be cleaned once a month using non aggressive detergents, either by
hand or in the dishwasher, which must be set to a low temperature and a short
cycle. When washed in a dishwasher, the grease filter may discolour slightly, but
this does not affect its filtering capacity.
To remove the grease filter, pull the spring release handle.
Maintenance of the charcoal filter
It absorbs unpleasant odours caused by cooking.
The saturation of the activated charcoal occurs after more or less prolonged use,
depending on the type of cooking and the regularity of cleaning of the grease
filter.
In any case it is necessary to replace the cartridge at least every four mounths.
The carbon filter may NOT be washed or regenerated.
Assembly
Hook the charcoal filter at the back on the metal tongue of the hood first, then on
the front with the two knobs.
Disassembly
Remove the charcoal filter by turning the knobs fixing it to the hood by 90°.
