16
EN
Turning on the Appliance
Starting a wash cycle....
After performing all the operations described in the previous
paragraphs, turn the water tap on completely, open the
appliance door and press ON-OFF button "
A
": indicator light
"
B
" comes on. Your appliance is now on and awaiting
instructions.
Setting and Starting a Wash Cycle
Select the wash cycle by pressing button "
P
". Each time this
button is pressed, one of the indicator lights "
M
" will come
on in sequence, select the wash cycle you deem most suitable
for the type of dishes to wash (take a look at page 17, where
you will find the wash cycle table). Close the appliance door
and after a few seconds, you will hear a short beep: the
wash cycle has begun."
Cancelling or modifying a cycle while underway...
Premise
:
You can cancel the wash cycle in progress, if it has
only just started.
But if you have chosen the wrong cycle, not to worry! You
can modify the wash cycle in progress, if it has only just started.
Open the appliance door carefully to avoid any hot water
splashes, then keep button "
P
" pressed for approximately 5
seconds, until you hear 3 short beeps. Indicator light "
M
"
will come off and at this point, all the settings will have been
cancelled. You are now free to re-set the correct wash cycle.
If you forget to load some of the dishes...
Well, it happens to everyone. Interrupt the wash cycle by
opening the appliance door with the utmost care, as usual,
then insert the dish you had forgotten. When you shut the
appliance door, the cycle will start up from where you
interrupted it.
At the end of the wash cycle...
The end of the wash cycle is indicated by a double beep and
the flashing of the wash cycle indicator light "
M
".
Turn off the water tap.
Wait a few minutes before unloading the dishes: they are
very hot! If you wait a little while, they dry better thanks to
the steam.
Empty the lower rack first.
Make sure the wash cycle has ended before removing the
dishes!
Warning:
If opening the door soon after the end of the programme, or
during it, stand away from the Dishwasher, to avoid possible
injury from hot steam.
There's been a power failure? Have you opened the
dishwasher door?
The wash cycle stops and then restarts when the electricity
comes back on or when you close the door.
Do you want extra drying?
Press button "
E
" before you start the selected wash cycle.
A prolonged beep will inform you that you have selected
extra drying, a short beep indicates it has been disabled.
With extra drying, the wash cycle will last longer, to provide
you with drier dishes.
Setting The Start Delay Time
When you have loaded the dishes, you can choose when to
start your dishwasher before setting the desired wash cycle.
Press button "
C
" to delay the start of the wash cycle by 6, 4
or 2hours. Each time you press it, you will hear a short beep
and indicator light "
D
" corresponding to the selected delay
will come on.
Now you can select the desired wash cycle. Close the
appliance door and, after you hear the beep, the countdown
to the delayed start will begin.
Once this time is up, the indicator light will stop flashing and
the wash cycle will begin.
If you change your mind and you wish to set a different
delay, just open the appliance door, press button "
C
" and
repeat the selection.
If, on the other hand, you want to cancel the delayed start
set and you want the wash cycle to start immediately, press
the button repeatedly until indicator light "
D
" comes off.
When you close the appliance door, the wash cycle starts up
and a short beep sounds.
If the power to the appliance goes off or the door is opened
during the delay period, the clock will stop the countdown. It
will start again when the power has come back on, or when
the door has been closed.
You want to wash on one rack only?
Remember to use half the amount of detergent.
Your dishwasher also allows you to wash half a load, to save
water and electricity. Before setting any wash cycle
whatsoever, press button "
Q
" repeatedly to select whether
you want to run a half cycle on the upper or lower rack.
Each time you press it, you will hear a short beep and indicator
light "
R
" corresponding to the selected rack will come on.
Warning!
Open the dishwasher door, turn off by pressing button
“
A
”, unplug the appliance from the electricity socket to
cut off the power supply;
the power supply cable should
consequently be easily accessible.
