background image

VME64x System Subrack 2 U

Product Definition

20836-245

www.schroff.biz

6

R1.0, July 14, 2009

2.4  Power Supply

The VME64x system can be powered by plug-in power supplies with wide range 
input (100 - 240 VAC), Schroff order-no. 13100-141.

The power supplies can be plugged-in in dedicated slots at the right front side. 
The power supplies contact via 47-position connectors to the power backplane. 

The power input is provided by a AC mains/line module with IEC 320-C14  
connector, integrated mains/line fuses and line filter.

The fuse rating is 8 A slow blow.

Figure 2: AC Terminal - Grounding

2.4.1  Grounding/Earthing

There is a 6,3 mm faston connector at the rear panel. This connector is only for 
equipotential bonding. Grounding is achieved through the protective earth 
conductor of the power cable!

Hazardous voltage!

Parts of the power supply may be exposed with hazardous voltage. Always
remove mains/line connector before carry out any assembly work.

Caution!

Your system has not been provided with a AC power cable. Purchase a
AC power cable that is approved for use in your country. The AC power cable 
must be rated for the product and for the voltage and current marked on the 
product's electrical ratings label. The voltage and current rating of the cable 
should be greater than the ratings marked on the product.

10009832

1

Fuseholder

3

AC Connector (IEC320-C14)

2

Mains/line switch

4

6,3 mm faston connector

Caution!

The unit is designed in accordance with protection class 1! It must therefore be 
operated with protective earth/GND connection. Use only a three conductor 
AC power cable with a protective earth conductor that meets the IEC safety 
standards!

Summary of Contents for VME64x























Reviews: