background image

05

2. Product description.

2.1 General information

follow-me momo.

 is the clever parent-child tandem coupling for tricycles 

and unites riding pleasure and safety. With the 

follow-me momo.

 your entire 

family is always safe when enjoying a bicycle ride. When your child gets 

tired or traffic is chaotic, simply couple your child`s tricycle to your own 

bicycle. The clever parent-child tandem coupling lets you react quickly to 

approaching situations without having to use any tools! As soon as you 

estimate your child to be safe again, they can ride independently once 

more. The 

follow-me momo.

 in size 1 couples Schuchmann tricycles to 12“. 

Size 2 is suited for tricycles in 16“ and 20“. 

follow-me momo.

 in size 3 pulls 

tricycles in sizes 24“ and 26“.

2.2 Application areas, use according to the intended purpose

follow-me momo.

 is suited for use on tarred roads, cycle tracks and dirt ro-

ads with fine gravel on the surface. Cyclists over 16 years may carry along 

a child / a youth with the 

follow-me momo.

 if the child/youth can push the 

pedals while sitting down.

Please observe: Only momo tricycles (from 2008) by Schuchmann without elec-

tric drive may be coupled! Do NOT couple momo therapy bicycles or therapy 

bicycles and tricycles from other manufacturers.

2.3  Use not in accordance with the intended purpose / warning guide-

lines

• Check the 

follow-me momo.

 prior to each ride for loose screws,  

breakage and deformation.

• Check all quick-release clamps, screw connections and plug-in 

connections (folding pin).

• Regularly check the air pressure and tyre condition of the leading  

bicycle and the tricycle.

• Always check your bicycle rims for any damage or dangerous abrasion 

through the rim brakes.

• Conduct a brakes test and ensure that the brake linings on all rim  

brakes are fully aligned to the rim flanks and that the brake surfaces are 
clean and grease-free.

• It must not be possible to pull the brake lever through to the handlebars.
• The combination of leading bicycle and tricycle are considered a unit, 

meaning that the regulations applicable for bicycles e.g. with regard to 
illumination (if necessary, equip the tricycle with battery-operated illumi-
nation) and reflectors must be maintained.

• Regularly check the function of the light system on the leading bicycle 

and the tricycle.

• Also check both bicycles in accordance with the instructions given by  

the bicycle manufacturer.

Summary of Contents for follow-me momo

























Reviews: