MAINTENANCE
FX-530 06/21
Maintenance Section 5-16
© 2021 Alamo Group Inc.
MAINTENANCE
Tightening Instructions for 517 & 511 Hubs
Proper setting for the tapered roller bearings is described in the following procedure. Always use a new cotter
pin when making adjustments to the hubs.
1. Tighten the castle nut to 20 foot pounds while turning hub. Then back the nut off 1/2 of a turn. Spin the hub
2 or 3 times. While slowly turning hub clockwise, finger tighten the castle nut until castle nut notch lines up
with hole in axle. If notch will not line up, back off nut to next notch.
2. Put the cotter pin in the axle hole. Before bending the cotter pin, spin the hub. The hub should free wheel
from 1 to 2 full turns.
3. If the hub spins the right amount, finish installing the cotter pin by bending the ends.
4. Coat the inside of the dust cap with a thin coat of grease by using your finger. Then install on hub using the
right dust cap driver.
5. Wipe off all excess grease from hub and axle.
There should not be any drag noticed when spinning a tire installed on a hub. If the axle nut
is too tight, the rollers of the wheel bearings will remove the grease from the bearing races,
decreasing the life of the bearings.
Tires
Periodically check tire pressure. Tires should be
inflated to manufacturer’s suggested specifications.
Higher pressures may cause excessive bouncing
over rough ground. Lower pressures may cause
excessive wear. Recommended pressures are
shown in chart.
Do not replace center section tires with wing tires
removed.
Do Not exchange the center tires with the wing tires. These are different tires and doing so
can result in damage to the rotary cutter.
To remove tires for repair or replacement, lower the wings to the ground and install the center transport lock
pin. Relieve hydraulic pressure Shut off tractor, apply parking brake and disengage PTO. Loosen the wheel
bolts with wrench. DO NOT remove them. Use a hydraulic jack to lift the back end of the cutter frame near the
wheel standard. Securely block the wheel standard so the tire can spin freely before removing the wheel bolts.
Summary of Contents for FX-530
