44
Memory function (ex factory
OFF
)
Select «Extended basic settings»!
If the memory function is switched on, the selected
temperature and spin additional functions are saved for
each programme. If the same programme is selected
again, the stored values are automatically used.
The values can then be altered.
Soap wash programme (ex factory
OFF
)
Select «Extended basic settings»!
When this programme is switched on, an extra rinse is
added.
Soak programme (ex factory
OFF
)
Select «Extended basic settings»!
When this programme is switched on:
soaking time of up to 12 hours.
X
After the programme is selected, set the desired
soaking time by pressing the «Start time preselection»
button.
The soaking time set or remaining is displayed until
the programme starts (1-12 hours).
X
The soaking time starts when the start button is
pressed.
Notes
:
X
Add soaking detergent in section
I
of the detergent
drawer and your usual detergent in section
II
.
The soaking programme must be reprogrammed for
each wash.
Soaking can be interrupted and the wash programme
started by pressing the quick wash button.
The current soaking time is stored in the event of a
power cut. The duration of the power cut is not taken
into account.
Cool down function (ex factory
OFF
)
Select «Extended basic settings»!
Detergent solution cooling: When the detergent solution
cooling function is switched on, boiling water is cooled
with cold water at the end of the washing process.
This helps to prevent damage to older drains.
This cooling always takes place in the easy care and Super-
finish pro grammes, irrespective of this setting. This helps
to prevent creases.
Loosening up at programme end (ex factory
ON
)
Select «Extended basic settings»!
When this function is selected, the laundry is tumbled
for 5 minutes at the end of the programme.
LCD Brightness (ex factory
220
)
Select «Extended basic settings»!
The
button can be used to alter the brightness of
text on the display.
LCD Contrast (ex factory
26
)
Select «Extended basic settings»!
The
button can be used to alter the contrast on
the display.
Alarm volume (ex factory
Volume 2
)
Select «Extended basic settings»!
With the Alarm setting switched on, a signal sounds at
regular intervals at the end of the programme. The level
can be adjusted in 3 levels using the
button.
Off
Volume 1
Volume 2
Volume 3
Standby function (ex factory
ON
)
Select «Extended basic settings»!
When the standby function is switched on, the controls
switch off in energy saving mode when no wash pro-
gramme is running or no button is pressed. The display
will show «ZZZ».
Optical interface (ex factory
OFF
)
Select «Extended basic settings»!
If the optical interface (SCS) is switched on, customer
services can communicate with the machine by PC.
Reduced mains power (ex factory
OFF
)
Select «Extended basic settings»!
If the connected load is reduced, the programme times
will be extended accordingly.
Off = 400V 2N ~ 4,0 kW / 10 AT
Off = 230V 1N ~ 4,0 kW / 16 AT
On = 230V 1N ~ 2,1 kW / 10 AT
Default language (ex factory
GERMAN
)
Select «Extended basic settings»!
If another language is temporarily selected via the
buttons
and
, after programme end, in stand by
mode or after a long standstill, the setting reverts back
to the default language.
Door open at programme end (ex factory
OFF
)
Select «Extended basic settings»!
If this function is switched on, the door will open auto-
matically at the end of the programme.
Information for testing institutes and users
Energy labelling according to Directive 2010/30/EU and
EN 60456 is based on the «ecoPlus» programmes for
coloureds at 60°C, full and half loads, and coloureds at
40°C, half loads.
Annual energy consumption: 175 kWh
Annual water consumption: 9300 litres
