• 7 •
USING THE USB PORTS
NOTE:
The 2 left ports are optimized for
Android
™
devices. The 2 right ports are
optimized for Apple
®
devices.
The USB ports provide up to 2A per side
(4A total) at 5V DC.
1.
Ensure that the battery clamps are
securely clipped on the storage holders.
2.
Plug the device into one of the four
USB ports on the front panel.
3.
Press the USB port ON/OFF button.
4.
Turn on the USB device.
5.
When you are finished using the USB
port, press the button, to turn off.
6.
Charge the jump starter as soon as
possible after using the USB port.
NOTE:
To protect your electronic devices,
the USB will automatically shut off when
the internal battery’s voltage is low.
POWERING A 12V DC DEVICE
The portable power is a power source for
all 12V DC accessories that are equipped
with a 12V accessory plug. Use it for power
outages and on fishing or camping trips.
NOTE:
Do not power a 12V device with
the portable power while charging the
internal battery.
1.
Make sure the device to be powered
is OFF before inserting the 12V DC
accessory plug into the 12V DC
accessory outlet.
2.
Ensure that the battery clamps are
securely clipped on the storage holders.
3.
Open the protective cover of the DC
power outlet on the portable power .
4.
Plug the 12V DC device into the DC
power outlet and turn on the 12V DC
device (if required).
5.
When finished, turn off the DC device
(if required) and unplug from the DC
power outlet.
CAUTION:
Do not use the portable power
to run appliances that draw more than
20A DC.
NOTE:
Extended operation of a 12V DC
device may result in excessive battery drain.
Recharge the portable power immediately
after unplugging the 12V DC device.
12V DC ESTIMATED RUN-TIMES
APPLIANCE TYPE
EST
WATTAGE
ESTIMATED
RUN TIME
Cell phone
4 watts
54 hrs
Fluorescent light
4 watts
54 hrs
Radios, fans
9 watts
24 hrs
Depth finder
9 watts
24 hrs
Camcorder
15 watts
14.4 hrs
Electrical tool
24 watts
9 hrs
Electric cooler
48 watts
4.5 hrs
Car vacuum,
air compressor
80 watts
2.7 hrs
NOTE:
Actual time may vary. Times are based
on a fully charged internal battery.
USING THE AIR COMPRESSOR
WARNING.
Read the instructions of the
product to be inflated before using the
compressor. Avoid overinflation; do not
exceed the manufacturer’s recommended
pressures. Do not leave the air compressor
unattended during use.
1.
Remove the air compressor hose from
the storage compartment in the back of
the portable power.
2.
Connect the adapter to the valve stem
by threading it onto the end. If necessary,
use one of the additional adapters.
3.
Press the
Compressor
button.
4.
To select the desired PSI, press the
“
+
” or “
–
” buttons. When done, press
the
SET
button.
5.
When the desired pressure is reached,
the compressor will turn off. Unthread
the connector from the valve stem.
6.
Press the
Compressor
button
again, to turn off the display and LEDs.
7.
Do not run for more than 10 minutes
at a time. Allow the jump starter to cool
down for 10 minutes before using again.
8.
When finished, return the air
compressor hose to the storage
compartment in the back of the unit.
9.
Allow unit to cool.
10.
Recharge the unit before storing.
NOTE:
To prevent overheating, the
compressor has built-in thermal protection
that will turn the compressor off before it
overheats. If the compressor shuts off,
wait a few minutes and it will automatically
restart when the compressor cools.
NOTE:
When not in use, the compressor
will automatically shut off after 2 minutes.
NOTE:
The air compressor is rated for
100 PSI maximum.
ESTIMATED TIME FOR INFLATING
Vehicle Tires 13"-16"
6-24 minutes
Bike Tires
1-3 minutes
Sports Balls
30 seconds
Times are approximate. Use the air compressor
gauge to ensure the proper pressure has been
reached. Do not overinflate.
BEFORE USING THE CONVERTER
Important Safety Instructions:
1.
Keep the portable power well ventilated,
in order to properly disperse heat
generated while it is in use. Make sure
there are several inches of clearance
around the top and sides, and do not
block the vents on the back of the
portable power.
2.
Make sure the portable power is
not close to any potential source of
flammable fumes or clothing.
3.
Keep the portable power dry.
