SCHÜTTE Ocean, Installation Instructions Manual

8

GB

Installation instructions

Dear customer,

You have purchased a high-quality and long-lasting product 

from our line of goods. Please read these instructions care-

fully before assembling and observe the notes.

Therefore, keep the instructions in a safe place and pass 

them on to possible subsequent owners.

Safety notes

•  Only allow experts carry out the installation work.

•  

CAUTION DAMAGE BY WATER!

Prior to installation please turn the general water supply 

off.

• Ensure that all gaskets have the correct fit.

•  These taps are not suitable for use on low pressure and 

small electrical storage heaters.

•  We recommend the installation of a filter into the appli-

ance or at least the use of angle valves with filter, in order 

to avoid   the inflow of foreign matter, which could dam-

age the upper parts of the valves.

•  This tap is only intended for use in private households! 

Only suitable for use in rooms with a temperature over 0 °C, 

when there is danger of frost, sut off the water supply and 

empty the tap.

•  Take care when adjusting the warm water. Danger of 

scalding!

•  Incorrectly installed fittings can cause water damages!

•  Despite careful production, sharp edges can occur. Please 

exercise caution!

•  Risk of injury in case of damage to the shelf. 

Disposal

Your washbasin tap is delivered in a solid packaging, in or-

der to protect it against transport damages. The packaging 

consists of recyclable materials. Dispose it in an environ-

mentally suitable manner.

Do not throw the product into the normal domestic waste at 

the end of its service life, but ask your municipal administra-

tion about the possibility of an environmentally friendly 

disposal.

Technical data

•  Flow pressure: Recommended as 1.5 to 6 bar; in case of 

more than 6 bar connection pressure, we recommend that 

a pressure reducer is installed

• Water temperature: max. 80 °C

 Installation Instructions

•  After installing the tap please unscrew the mixer nozzle, 

flush the pipeline and the tap thoroughly for a longer time, 

in order to flush out contaminations and residues.

•  Check all connections carefully after first-time use to make 

sure that they are tight.

•  We do not assume any warranty for incorrect installation - 

in particular for subsequent damages!

Instructions for care

Sanitary taps require special care. Therefore, please observe 

the following instructions:

•  Chrome-plated surfaces are sensitive to lime-dissolving 

agents, acidic cleaning agents and all kinds of abrasives.

•  Never clean coloured surfaces with abrasive, corrosive, or 

alcoholic agents.

•  Only clean your taps with clear water and a soft cloth or a 

shammy.

Maintenance

•   Please observe that the upper part of the valve and the 

thermostat element are wear parts, and that these may 

have to be replaced in case of hard water or dirty water 

every 1-2 years. 

•  Please check all joints and connections for leaks or visible 

damages at regular intervals.

•  In case of any leaks or visible damages to the fitting or con-

nection hoses, these should be immediately checked by a 

specialist and replaced if necessary.

Decommissioning

•  Cut off the water supply before dismantling the product. 

• Pay attention to escaping residual water.

•  Disassemble the product in the reverse order of the as-

sembly instructions.

  

The illustrations are to be considered as 

figurative representations, deviations of the product are 

possible. Subject to technical modifications.

WARRANTY CARD

The Franz Joseph Schütte GmbH, based in Wallenhorst, 

shall take on a manufacturer’s warranty for the product you 

have procured in accordance with the warranty conditions 

stated below. Your legal warranty claims from the purchase 

contract with the seller and your legal rights shall not be 

limited by this warranty.  

Warranty conditions:

1. Scope of warranty 

The Franz Joseph Schütte GmbH shall grant a warranty 

for proper material qualities and material processing in 

accordance with the intended purpose as well as professi-

onal assembly, tightness and function. The warranty shall 

only apply for the country in which the product has been 

procured. 

Included within the scope of the warranty is a guarantee, re-

duced to 1 year, for the durability of non-high-gloss chrome-

plated surfaces, such as bronzed or coloured surfaces.  

Excluded from the warranty are the following:

• Valve

•   Damages due to improper assembly, commissioning and 

handling  

•  Damages due to external influences such as fire, water and 

chemical influences 

•  Mechanical damage due to accidents, falls or impacts 

•  Negligent or intentional destruction

•  Normal wear or poor maintenance  

•  Damages due to repairs by unqualified persons

•   Improper handling, insufficient care and use of unsuitable 

cleaning agents