USER MANUAL ZHS15
ADAPTER PLUG
AS CONSUMPTION GAUGE
ZHS15
MANUFACTURER INFORMATION
Dear Customer,
should you require technical advice and your
retailer could not help please contact our
technical support.
BDA_ZHS15
HOME AUTOMATION
Congratulations and thank you for purchasing the Schwaiger ZHS15 product. Below
you will find useful operating guidelines.
Device Description
Adapter Plug ZHS15 (shown in figure 1) is wirelessly controlled electronic switch with overload
protection and power measurement features. It can operate as a part of Schwaiger Home Au-
tomation System.
ZHS15 has Socket Type F
and Plug Type E.
Figure 1: ZHS15
BUTTONS/FUNCTIONS
Normal mode
1. Short press - single
On/Off command
LED indication
2. Long press [more than 2 sec]
If button is released in this period, device will be switched to the SETUP operating mode. LED
indication: blue lighting continuously not more than 5 seconds.
3. Short press - 5x
Set/Reset power limit command.
LED indication: 3x green blink
Setup mode
1. Short press - single
Join ZigBee network
2. Short press - 7x
Device will be reset to the factory settings. Upon reset device is switched to NORMAL operation
mode. LED indication: red will lighting for 2 seconds.
POWER LED INDICATION
In NORMAL operation mode LED is used for active power indication. If Smart Plug is in OFF sta-
te, power LED indication will be white. If plug is in ON state, power LED indication will indicate
active power according to following Figure 1. Active power consumption a power consumption in
percentage according to user defined Power limit value.
Color ...................... Active Power [%]
White ...................... 0 (OFF state)
Yellow ..................... 0%
Green ..................... 10%
Cyan ....................... 30%
Blue........................ 50%
Magenta .................. 80%
Red ........................ 100%
Technical data
Preparations
All ZHS15 (installation group) that are going to be a part of the home system should be installed
(inserted into the sockets). After powering for the first time ZHS15 is not associated with any
ZigBee network. To start configuration of Smart Plug, it must be in SETUP operation mode.
Join the new plug to the Gateway:
Use next steps:
1. Now click on your smartphone or tablet (Schwaiger app) sequentially following menu items:
2. „Home Installation” – „Add device” – „Find device”
3. Hold down main button until LED indicator starts lighting blue (approx. 2-3 sec.)
4. Make one short button press again to start joining to the network.
5. During join routine, indication will blink red. After successively joining to the network, LED-
will blink green – no longer than 3 minutes. Long button press will terminate green blinking
immediately.
Note: Please note, that the distance between the devices and the gateway must bee about 0,5m
during integrating.
Switching to SETUP mode
To enter the SETUP mode, hold down device button until LED indicator starts lighting blue
(approx. 2-3 seconds). After release, LED will indicate blue continuously 5 more seconds and
Smart Plug will be in SETUP mode. Smart Plug change state to NORMAL mode automatically upon
5 seconds or when user set command successfully.
Switching back to NORMAL mode:
Smart Plug changes its operation mode from SETUP mode to NORMAL mode automatically when
user gives a button command or after the 5 seconds from entering the SETUP mode. Upon swit-
ching to NORMAL operation mode, LED will indicate active power (white if load is not connected
or it power is approx 0W).
POWER LIMIT
ZHS15 has two overload protection limits. Current threshold is fixed and set to around 16A. Second
limit is a user configurable power limit which can be set in range [10 - 3500W]. If either limit is excee-
ded for a period of approximately two seconds, the load will be disconnected and indication lights will
blink in red to indicate overload. In case of overload, manual on/off and over-the-air on/off commands
are disabled. Five consecutive short presses will reset power limit settings to 3500W and re-enable on/
off command. Alternatively, to enable on/off command again without reseting user power limit, plug
should be reinserted to the home socket. The power limit is 3500W/16A factory defined.
Set user power limit on the desire value
• The outlet must be on with referent consumer.
• Make five consecutive short presses. After successfully inserted sequence, the power limit
is changed to referent consumption (current consumption of a consumer) with some margin.
LED indication: 3 x green blink.
Reset user power limit
• ZHS15 must be without a consumer and in NORMAL mode.
• Make five consecutive short presses. After successfully inserted sequence, the power limit is
changed to maximum (3500W). LED indication: 3 x green blink.
FACTORY RESET
Factory reset is used to delete all stored ZigBee network data, working mode setting etc. If de-
vice is not in SETUP operation mode, follow: Switching to SETUP mode section. Upon switching
to SETUP operation mode (LED indication lights blue continuously) make 7x short consecutive
presses and plug will be reset to the factory defaults.
NOTE: The power limit is approx. 3500W factory defined.
2 – LED indicator
1 – Main button
POWER SUPPLY
~110 – 230 V
50 – 60 Hz
OPERATING TEMPERATURE
0 - 40° C
DIMENSIONS
86 x 44 x 44 mm
COMMUNICATION
IEEE 802.15.4
2,4 GHz
RADIO PROTOCOL
ZigBee
MAX. LOAD RATINGS
3500 W / 16 A (cos φ > 0,90)
PROTECTION DEGREE
IP20
SWITCH CONSTRUCTION
µ (Relais)
Schwaiger GmbH
Würzburger Straße 17
90579 Langenzenn
Hotline: +49 (0) 9101 702-199
www.schwaiger.de
homeautomation@schwaiger.de
Business hours:
Monday to Thursday:
08:00 - 17:00
Friday:
08:00 - 14:30
WARNINGS & CONSIDERATIONS
WARNING!
Improper use or installation can cause SERIOUS INJURY, DEATH or LOSS/DAMAGE
OF PROPERTY.
WARNING!
Using ZHS15 device in a manner other than outlined in this document is not allowed.
CAUTION!
Do not try to open or to repair a device, please contact authorized person. Otherwise,
SERIOUS INJURY, DEATH or LOSS/DAMAGE OF PROPERTY is possible.
IMPORTANT!
Do not overload this device above the recommended output.
Disposal information
This is an electrical device. It can be disposed of free of charge at specified disposal sites.
EC Declaration of Conformity
„Hereby Schwaiger GmbH declares that the product ZHS15 is in compliance with the essential re-
quirements and other relevant provisions of Directive 1999/5//EC.” The Declaration of Conformity
can be found at the following address:
http://www.schwaiger.de/downloads
