background image

lunaSchwank 

 Technical Instructions 

 

 

Safety distances to combustible materials 

lunaSchwank 6, 9 and 12 with wall bracket 

The heater can be swivelled at its suspension point [M8 cylindrical screw with inner hexagon]. Angular measure a 

min. 25° 

– 

max. 45° [between burner surface and horizontal]. 

 
 
 
 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Max. temperatures in the ceiling and wall area: 85°C 

– 

at an air flow of at least 0.25 m/s 

 

Device type without hood 

Distance B 

Distance C 

lunaSchwank 6 

Min. 750 mm 

Min. 600 mm 

lunaSchwank 9 

Min. 810 mm 

Min. 650 mm 

lunaSchwank 12 

Min. 850 mm 

Min. 800 mm 

 
 

Device type with hood 

Distance B 

Distance C 

lunaSchwank 6 

Min. 450 mm 

Min. 600 mm 

lunaSchwank 9 

Min. 560 mm 

Min. 650 mm 

lunaSchwank 12 

Min. 600 mm 

Min. 800 mm 

 
Lateral safety distance:    

200 mm 

– 

lunaSchwank 6

 

 

 

 

250 mm 

– 

lunaSchwank 9 

 

 

 

 

350 mm 

– 

lunaSchwank 12 

 

The given safety distances apply only to the shown installation of the heater or the 

 hood with original Schwank wall bracket. 

Minimum suspension height according to possible angles of suspension 

                                                                                     

 

 

 

 

Angle of suspension a 

25° 

– 

45° 

  

lunaSchwank 6 

2100 mm 

  

lunaSchwank 9 

2600 mm 

 

lunaSchwank 12 

3000 mm 

 

Without hood 

 

With hood 

 

[measured from the outer edge of 
housing]

 

Summary of Contents for lunaSchwank 12






















Reviews: