2
Command Summary
Date Code 20010625
SEL-311L Instruction Manual
HIS
n
Show brief summary of the
n
latest event reports.
HIS C
Clear the brief summary and corresponding event reports.
IRI
Force synchronization attempt of internal relay clock to IRIG-B time-code input.
MET
k
Display instantaneous metering data (currents and alpha plane) for local and remote terminals. Enter
k
for repeat count.
MET B
k
Display instantaneous metering data for local terminal including voltage. Enter
k
for repeat count.
MET D
Display demand and peak demand data. Enter MET RD or MET RP to reset.
MET E
Display energy metering data. Enter MET RE to reset.
MET M
Display maximum/minimum metering data. Enter MET RM to reset.
QUI
Quit. Returns to Access Level 0. Terminates SEL Distributed Port Switch Protocol (LMD) protocol
connection. Available in all access levels.
SER
n
Show the latest
n
rows in the Sequential Events Recorder (SER) event report.
SER
m n
Show rows
m
through
n
in the Sequential Events Recorder (SER) event report.
SER
d1
Show rows in the Sequential Events Recorder (SER) event report from date
d1
.
SER
d1 d2
Show rows in the Sequential Events Recorder (SER) event report from date
d1
to
d2
. Entry of dates is
dependent on the Date Format setting DATE_F (= MDY or YMD).
SER C
Clears the Sequential Events Recorder (SER).
SHO
n
Show relay settings (overcurrent, reclosing, timers, etc.) for Group
n
.
SHO L
n
Show
SEL
OGIC
®
control equation settings for Group
n
.
SHO G
Show global settings.
SHO P
n
Show
Port
n
settings.
SHO R
Show Sequential Events Recorder (SER) settings.
SHO T
Show text label settings.
STA
Show relay self-test status.
SUM
Show newest event summary.
SUM A
Acknowledge oldest even summary.
SUM N
View oldest unacknowledged event report.
SUM N [A]
Display or acknowledge event summary number “N”.
TAR R
Reset the front-panel tripping targets.
TAR
n k
Display Relay Word row. If
n
= 0 through 45, display row
n
. If
n
is an element name (e.g., 50G1)
display the row containing element
n
. Enter
k
for repeat count.
TIM
Show or set time (24 hour time). Show time presently in the relay by entering just TIM. Example time
22:47:36 is entered with command TIM 22:47:36.
TRI
Trigger an event report.
Access
Level B
Commands
Access Level B commands primarily allow the user to operate output contacts. All Access Level 1
commands can also be executed from Access Level B. The screen prompt is: ==>
BRE
n
Enter BRE W to preload breaker wear. Enter BRE R to reset breaker monitor data.
CLO
Close the circuit breaker. See the Note in the
Set Close
discussion, following Figure 6.1 for more
information concerning the CLO command.
GRO
n
Change active group to Group
n
.
OPE
Open the circuit breaker. See the Note following Figure 5.2 and the Note in the
Lockout State
discussion, following Table 6.1 for more information concerning the OPE command.
PUL
n k
Pulse output contact
n
(OUT101–OUT107, ALARM, OUT201–OUT212) for
k
(1–30) seconds.
Parameter
n
must be specified;
k
defaults to 1 if not specified.
Summary of Contents for SEL-311L
