manualshive.com logo in svg

Schweitzer Engineering Laboratories SEL-700G Series, Instruction Manual

The Schweitzer Engineering Laboratories SEL-700G Series Instruction Manual is your comprehensive guide to effectively operate and maintain your SEL-700G product. This essential manual is available for free download from 88.208.23.73:8080, ensuring easy access to valuable information to maximise the performance of your SEL-700G Series.

Share
Download
background image

4.25

Date Code 20170814

Instruction Manual

SEL-700G Relay

Protection and Logic Functions

Group Settings (SET Command)

Restraint Slope Percentage.

The purpose of the percentage restraint 

characteristic is to allow the relay to differentiate between differential current 
from an internal fault versus differential current during normal or external 
fault conditions. You must select slope characteristic settings that balance 
security and dependability. To do this, it is helpful to determine what slope 
ratio is characteristic of normal conditions (slope must exceed that for 
security) and what slope ratio is characteristic of an internal fault (the slope 
must be below that for dependability). In the case of the SEL-700G1 Relay, 
the slope ratio for a bolted internal fault is 100%. 

The sources of differential current for external faults fall into three categories:

➤

Differential current that is not proportional to the current flow 
through the zone (steady state).

➤

Differential current that is proportional to current flow through 
the zone (proportional).

➤

Differential current that is transient in nature (transient).

SLP1 should be set above normal steady-state and proportional errors. SLP2 is 
used to accommodate transient errors. The following is a list of typical sources 
of error that must be considered.

➤

Excitation current (typically 1 to 4%)

➤

CT accuracy (typically less than 3% in the nominal range)

➤

No-Load Tap Changer (NLTC) (typically ±5%)

➤

Load Tap-Changer (LTC) (typically ±10%)

➤

Relay accuracy (±5% or ±0.02 • I

NOM

, whichever is largest.)

We recognize that the excitation current of the transformer is not proportional 
to load flow. However, a conservative approach would include it as a 
proportional error. 

CTs create both steady-state and transient errors, which can result in false 
differential current. IEEE Standard Requirements for Instrument 
Transformers, IEEE Standard C57.13-1993 specifies that a relay-accuracy CT 
must be 3 percent accurate at rated current and 10 percent accurate at 20 times 
rated current when ZB is the standard burden. It is important to note that the 
rated current specified in the standard is a symmetrical sinusoidal waveform 
(it does not have a transient DC component). Because the burden is usually 
designed to be much smaller than the standard burden, the error current will 
likely be much less than 3 percent for current flow at low multiples of the 
nominal rating of the CTs.

The errors can be added to determine the amount of error that the SLP1 
characteristic must accommodate for normal system conditions. At that point, 
use the following equation and add margin to determine SLP1 and determine 
the minimum limit of the allowable slope ratio.

where:

SLP1

MIN

 = slope ratio that will just accommodate Err with no margin

Err = amount of error expected in normal operation

k = AVERAGE restraint scaling factor (1 for the SEL-700G)

SLP1

M IN

%

Err%

200

Err%

–

k

------------------------------------------

100

=

Summary of Contents for SEL-700G Series

























































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SEL-700G Series

EVA Logik ZW12 User Manual preview
ZW12
Brand: EVA Logik Pages: 4
Pilz PNOZ X2 Operating Instructions Manual preview
PNOZ X2
Brand: Pilz Pages: 12
Fox Wi-R1S1-P Quick Start Manual preview
Wi-R1S1-P
Brand: Fox Pages: 15
Allen-Bradley 140MG-H Adjustment Instruction preview
140MG-H
Brand: Allen-Bradley Pages: 3
Viessmann 5551 Operation Manual preview
5551
Brand: Viessmann Pages: 4
ASO ELMON rail 32-242 Operating Manual preview
ELMON rail 32-242
Brand: ASO Pages: 32
ASO SK 32-31 Operating Manual preview
SK 32-31
Brand: ASO Pages: 44
Online AS400 Quick Start Manual preview
AS400
Brand: Online Pages: 6
Eaton EASY406-DC-ME Instruction Leaflet preview
EASY406-DC-ME
Brand: Eaton Pages: 8
Eaton ESR5-NO-31-UC Manual preview
ESR5-NO-31-UC
Brand: Eaton Pages: 42
GE P24DM Technical Manual preview
P24DM
Brand: GE Pages: 600
ABB CR Series Instruction Leaflet preview
CR Series
Brand: ABB Pages: 27
ABB REJ 525 Operator'S Manual preview
REJ 525
Brand: ABB Pages: 40
BURK Technology Plus-X Installation And Operation Manual preview
Plus-X
Brand: BURK Technology Pages: 11
System Sensor R-10T Installation And Maintenance Instructions preview
R-10T
Brand: System Sensor Pages: 2
OEZ 43239 Instructions For Use Manual preview
43239
Brand: OEZ Pages: 9
ABB CRN-1 Instruction Leaflet preview
CRN-1
Brand: ABB Pages: 12
KMC Controls CCE-3000 Series Installation Manual preview
CCE-3000 Series
Brand: KMC Controls Pages: 2

Brands by name

Popular brands

Load more brands