background image

4

safeTy WarnIng labels and serIal number

FCC Compliance

!

Changes or modifications to this unit not expressly approved by the party responsible for compliance could void 

the user’s authority to operate the equipment.

The machine and power supply comply with part 15 of the FCC rules. Operation is subject to the following two 
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, 
including interference that may cause undesired operation.

Note:

   This machine and power supply have been tested and found to comply with the limits for a Class B digital 

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against 
harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency 
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio 
communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause 
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the 
user is encouraged to try to correct the interference by one or more of the following measures:

•  Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
•   Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•   Consult the dealer or an experienced radio/TV technician for help.

•  Lisez et assimilez tous les avertissements  

  apposés sur cet appareil.

•  Gardez les enfants et les animaux de  

  compagnie éloignés de cette machine en  

  tout temps

• 

Déconseillé aux enfants âgés de    

  moins de 14 ans.

•  Lisez et familiarisez-vous avec le Manuel  

  du propriétaire et avec tous les    

  avertissements avant d’utiliser cette  

  machine.

•  Soyez prudent lorsque vous utilisez cet  

  équipement pour ne pas vous infliger de  

  graves blessures.

•  Cette machine supporte un poids   

  maximal de 300lbs. (136kg).

•  Remplacez toute étiquette  

 

  d’avertissement endommagée, illisible  

  ou manquante.

•  La fréquence cardiaque qui s’affiche  

  sur la console peut être inexact et  

  doit être utilisée seulement à titre  

  indicatif.

•  Read, understand and obey all  

 

  warnings on this machine.

•  Keep children away.

• 

Not intended for use by anyone  

  under 14 years of age.

•  Prior to use, read and understand  

  the Owner’s Manual.

•  Injury or death is possible if    

  Caution is not used while using this  

  machine.

•  The maximum user weight for this  

  machine is 300 lbs (136 kg).

•  Replace any “Caution”,  “Warning”  

  or “Danger” label that is illegible,  

  damaged, or removed.

•  The heart rate displayed may be  

  inaccurate and should be used for  

  reference only.

8002739_A

Serial number

Product 

specification

Summary of Contents for 170 Journey 1.5











Reviews: