background image

5

speCIfICaTIons

41.3” (105cm)

21.4” (54cm)

55.6” (141cm)

Before Assembly 

Select the area where you are going to set up and operate your machine. For safe operation, the location must be on a 

hard, level surface. Allow a workout area of a minimum 90” x 70” (2.3m x 1.8m).

Basic Assembly Tips

Follow these basic points when you assemble your machine:
1.   Read and understand the “Important Safety Instructions” before assembly.
2.   Collect all the pieces necessary for each assembly step.
3.   Using the recommended wrenches, turn the bolts and nuts to the right (clockwise) to tighten, and the left (counter-

clockwise) to loosen, unless instructed otherwise.

4.   When attaching 2 pieces, gently lift and look through the bolt holes to help insert the bolt through the holes.
5.  The assembly can require 2 people.

Maximum User Weight:

   300 lbs. (136 kg)

Power Requirements:

 

  Operational Voltage:  9VDC

  Operating Current:  1.5A

Regulatory Approvals:

  ISO 20957

   AC Power Adapter:  UL listed, Rated 120V 60Hz Input, 

9VDC, 1500mA Output. Class 2.

!

 This product, its packaging, and components contain 
chemicals known to the State of California to cause 
cancer, birth defects, or reproductive harm. This Notice 
is provided in accordance with California’s Proposition 
65. If you would like additional information, please refer 
to our website at www.nautilus.com/prop65.

Summary of Contents for 170 Journey 1.5











Reviews: