Bravo G4 17 / Bravo G4 22 / Bravo G4 28
62
EN
CYCLE
DESCRIPTION
NOMINAL VALUES
BASIC CYCLE
PARAMETERS
STERILISABLE MATERIALS
NOTES
Temp
e
ra
tu
re
(
°C)
P
re
s
s
u
re
(
b
a
r)
H
o
ldin
g
t
ime
(mi
n
.)
C
y
c
le
t
y
p
e
(
E
N
1
3
0
6
0
:2
0
1
4
+
A
1
:2
0
1
8
)
P
re
-v
a
c
u
u
m
(F=
fr
a
c
tion
a
te
d
;
S
=
s
in
g
le)
S
ta
n
d
a
rd
d
ry
ing
(
mi
n
.)
***
Total
c
y
c
le
t
ime
(L
o
a
d
Max
.)
Max
.
H
2
O
c
o
n
s
u
mpt
ion
(
ml
/c
y
c
le)
A
v
e
ra
g
e
e
n
e
rg
y
c
o
n
s
u
mp
tion
(
k
W
h
/c
y
c
le)
TY
P
E
MA
X
.
TOT
A
L
MA
S
S
(
k
g
)
MA
X
.
MA
S
S
P
E
R
TR
A
Y
(
k
g
)
**
MA
X
.
MA
S
S
P
E
R
I
T
E
M
(
k
g
)
134°C SOLID
WRAPPED
134
2.1
4(*)
S
S
17
45
500
0.7
Solid instruments in
single pack
5.00
1.00
0.25
It is advisable to
use the 3-tray
configuration
Unwrapped solid
materials
9.00
1.20
0.50
XXX°C USER
(see note)
134
--------
121
2.1
--------
1.1
4÷30
--------
20÷30
n.a.
F/S 5÷30 n.a.
n.a.
n.a.
Unwrapped solid
instruments (other load
types are possible
depending on the user
settings)
n.a.
n.a.
n.a.
Variable
parameters
depending on the
settings made
HELIX/BD
TEST
134
2.1
3.5
-
F
1
24
-
-
Test device only
(without another load)
-
-
-
VACUUM
TEST
-
-0.8
-
-
-
-
18
-
-
Empty chamber
-
-
-
HELIX/BD
TEST
(executable in
sequence)
-
-
-
-
-
-
46
-
-
-
-
-
-
(*) To set a sterilisation time of 5.5 minutes, contact the Technical Service.
Single Pre-Vacuum = 1 pre-vacuum; -0.8 bar (see figures in the following pages).
Fractionated Pre-Vacuum = 3 pre-vacuum; -0.8 bar each (see figures in the following pages).
Definition of hollow loads in accordance with standard EN 13060:2014 + A1:2018.
The term “hollow loads” in this manual refers both to “narrow lumen” elements (paragraph 3.18 EN 13060:2014 + A1:2018) and “simple hollow”
elements (paragraph 3.30 EN 13060:2014 + A1:2018).
The term "hollow load B" refers ONLY to the elements defined as "simple hollow" (paragraph 3.30 EN 13060:2014 + A1:2018).
(**) The Max. Mass per Tray means the maximum load to be placed on each tray, respecting, anyway, the MAX. TOTAL MASS as device load
limit.
(***)
Depending on the type of load, it may be necessary to optimise drying using the extra drying function (8.1)
