background image

                                                                                     

  
 

 

                

 

Standard Warranty 

Applies Only Within the Continental United States 

 

SCIENTEMP WARRANTS TO THE ORIGINAL PURCHASER 
FIRST 18 MONTHS – 

The cabinet and all of its parts shall be free of defects in material and workmanship under 

normal use and service for a period of 18 months from the date the unit has been shipped from our facility. 
Scientemp’s sole obligation under this warranty shall be limited, at its option, to either repairing or replacing any 
part of the cabinet determined by an authorized service agent to be defective. Scientemp reserves the right to repair 
the freezer at our facilities. 
 

THE SCIENTEMP STANDARD WARRANTY DOES NOT COVER 
 
TRANSPORTATION COSTS – 

Scientemp shall not be responsible for transportation or incidental costs incurred 

in connection with the repair or replacement of a cabinet or any of its parts. 
 

ABUSE, MISUSE, ACCIDENTS – 

Scientemp shall not be responsible for parts or assemblies which upon 

inspection are determined by an authorized Scientemp Service Agent to have been subjected to misuse, neglect, 
alteration, accident, abuse, damage during transit or delivery, or by fire or flood.  
 

CONSEQUENTIAL DAMAGES – IN NO EVENT SHALL SCIENTEMP CORP BE LIABLE FOR 
SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, 
PRODUCT LOSS OR PRODUCT SPOILAGE CLAIMS, NOR FOR ANY DELAY IN THE 
PERFORMANCE OF THIS WARRANTY DUE TO CAUSES BEYOND ITS CONTROL. 
 
GENERAL 

The standard warranty and any service contract related to the STANDARD WARRANTY shall apply only to the 
products sold and used within the boundaries of the Continental United States. 
 
Users may file warranty claims either directly with Scientemp Corp, 3565 S. Adrian Hwy, Adrian, MI 49221, or 
with the seller from whom the cabinet was purchased. All claims must be supported by information concerning the 
alleged defect and specifically identified by the Serial Number of the cabinet. 
 

THERE ARE NO OTHER WARRANTIES EXPRESS, IMPLIED, OR STATUTORY, EXCEPT THIS 
WARRANTY, WHICH IS IN LIEU OF ALL OTHER WARRANTIES INCLUDING TO THE EXTENT 
PERMITTED BY LAW, ANY IMPLIED WARRANTY OR MERCHANTABILITY OR FITNESS FOR A 
PARTICULAR PURPOSE. 
 

DO NOT DRILL HOLES IN CABINET 

Refrigeration tubing and wiring is routed through the cabinet walls. Leaks, wet insulation or electrical problems 

caused by drilling holes are not covered by warranty. 

 

 

                   3565 S. Adrian Hwy 

 Adrian, MI 49221 

800-968-2653 

517-263-6020 

Fax  517-263-5492 

Summary of Contents for 43-1.7A












Reviews: