Page 25
6.3 SELECTING THE PROPER BLADE AND CUTTING SPEED
In cold sawing, there is no such thing as a general purpose blade. To achieve the best results from your
saw, proper blade selection is important. Each saw is shipped with a pitch (number of teeth) calculator,
which will help to determine the proper blade for your application.
When sawing flat stock or rectangular solid sections, determine the thickest section that will be cut and
use the equivalent square size on the pitch calculator to determine the proper blade.
The CPO-350 Variable Speed saw is designed to use a maximum 14 inch (350mm) diameter blade. We
recommend using smaller diameter blades if your application does not require the maximum diameter.
Using smaller diameter blades reduces the surface feet per minute and smaller blades provide greater
rigidity. Smaller diameter blades available from stock for this machine are a 12-1/2 inch (315mm) and a
10-3/4 inch (275mm). For available tooth styles in stock, REFER TO SECTION 11.0.
The chart below gives the surface feet per minute for the various diameter blades.
BLADE DIAMETER
SURFACE FEET PER MINUTE
INCH
MM
RPM’S
11
35
88
176
10-3/4
275
31
99
247
500
12-1/2
315
36
114
287
572
14
350
41
128
322
646
The proper blade speed is also important. The CPO-350 Variable Speed has an RPM range from 11 to
176. The heavier the material, the lower the RPM. The lighter the material, the higher the RPM.
The HT model (60-120 RPM) is recommended primarily for thin wall tube up to 1/8 of an inch (3mm)
wall thickness and nonferrous materials. The low speed (60 RPM) should be used for tubes with wall
thicknesses of one hundred thousandths (.025mm) and thicker and for solid sections of nonferrous
materials. The High speed (120 RPM) is recommended for thin walled tubes and nonferrous tubes and
profiles. Some materials will require test cuts at both speeds to determine the best speed for the
application.
The LT model (30-60 RPM) is recommended for cutting solid sections, alloy tubes and nonferrous
materials. The Low speed (30 RPM) is recommended for solid sections of mild steel and alloy tubes. The
high speed (60 RPM) is recommended for tubes and nonferrous materials. As with the HT model, some
materials will require test cuts to determine the best speed.
Summary of Contents for CPO-275
