Page 28
6.5 MITER LOCKING DEVICE
SEE FIGURE 10 ON THE FOLLOWING PAGE.
All models manufactured for domestic sales are equipped with a miter locking device which allows
quick set-up for mitering at 45 degrees, left and right, and 90 degrees for straight cutting. A miter
locking device is available as an option for models manufactured for international sales.
TO USE THE MITER LOCKING DEVICE:
1.
Unlock the tension handle (A).
2.
Push the miter lock release handle (B).
3.
Turn the head in the direction that you want to miter.
4.
Release the miter lock handle and continue turning the head until the pin snaps into the slot.
5.
Then, re-lock the tension handle. When locking the tension handle, do not over-tighten.
6.
The miter locking device can be fine adjusted if it does not stop at an exact 45. Loosen the
mounting bolts (F) and adjust the complete miter lock, left or right, to the desired position.
IF YOU WANT TO CUT MITERS OTHER THAN 45 DEGREES:
1.
Unlock the tension handle (A).
2.
Push the miter lock release handle (B) and turn the head to the desired angle by using the scale on
the saw.
NOTE: THE SCALE IS READ ON THE RIGHT SIDE OF THE VISE AT POINT (C), NOT IN
THE CENTER.
3.
Re-lock the tension handle (A). After a period of time, the tension handle (A) may need to be
adjusted if the head will not remain in the position that it was previously set.
TO RE-SET THE TENSION HANDLE:
1.
Remove the access panel on the back of the machine base.
2.
Move the tension handle (A) to its unlocked position.
3.
Loosen the jam nuts (D) on the adjustment bolts (E) and tighten the bolts finger tight, plus 1/4 of a
turn.
4.
Work the tension handle several times and re-tighten the adjusting bolts, if necessary.
5.
Re-tighten the jam nuts (D).
Summary of Contents for CPO-275
