Page 28
6.7 MATERIAL CLAMPING
All work pieces must be clamped securely in the vise. Any slippage of the material can result in broken
or damaged blades. The material should be clamped so that the contact surface between the material
and the blade is as small as possible. For this reason, when cutting flat stock material, we recommend
standing it up and cutting it through the thinnest section, whenever possible. We also recommend
cutting square tubing through the diagonal section and angle iron with the web up. Some thin walled
round sections and profiles will require special jaws to hold them.
FOR EXAMPLES, SEE FIGURE 7 ON PAGE 24.
6.8 STROKE CONTROL ADJUSTMENT
SEE FIGURE 9 ON THE FOLLOWING PAGE.
TO ADJUST THE UP AND DOWN STROKE OF THE SAW HEAD, USE THE FOLLOWING STEPS:
1.
With the machine’s power off, raise the hood of the saw.
2.
Using a 17mm wrench, loosen the bolt (A) on the lower stroke control (B) and let the stroke
control rest at the bottom of the slot.
3.
Place a piece of the material that you are going to cut in the saw vise and manually clamp it in a
position so that the saw blade will not contact the material when the head comes down.
4.
Close the hood. The saw will not run with the hood open.
5.
Make sure that the motor switch (D) is in the OFF position so that the saw blade does not turn
while performing this setup.
6.
Power the saw and press the HEAD DOWN button (E).
7.
When the blade has passed the material in the vise by approximately 1/8 of an inch (3mm), stop
the head movement by turning off the flow control valve (F) and turn off the air pressure by
sliding the shuttle valve (G) down.
8.
Turn the power off. Raise the hood and bring the lower stroke control (B) up to the head stop and
lock it in place.
9.
Bring the upper stroke control (C) down to the head stop and lock it in place.
10.
Turn the air back on by moving the shuttle valve (G) up and open the flow control valve (F) one
turn.
11.
Loosen the bolt (A) on the upper stroke control (C) and allow the head to move slowly up until the
blade is approximately 1/8 of an inch (3mm) above the material in the vise. Tighten the bolt in the
upper stroke control.
Summary of Contents for CPO-315-HFA-5HP
