Page 33
1.
Set the shuttle vise indicator to the desired length by loosening the moving stop (M) and move it to
the length desired on the scale and re-tighten it. These bolts must be locked down tight, to prevent
the length setting from changing while the saw is in operation. Check them periodically
throughout the day.
2.
Place the HITCH FEED switch (G) in the desired position.
3.
Adjust the shuttle vise and material vise for the size of material. Adjust the vises up to the
material, allowing approximately 1/8 of an inch (3mm) clearance for the throw of the cylinder.
4.
Set the upper and lower stroke of the saw head. For instructions, REFER TO SECTION 6.8.
5.
Place the main power switch (A) in the ON position and the motor control switch (B) in the ON
position.
6.
Place the AUTO/MANUAL switch (I) in the MANUAL position and pull the EMERGENCY
STOP switch (D) out.
7.
Place the material to be cut in the material vise jaws so that 1/4 to 1/2 inch extends past the blade
slot.
8.
Press the POWER UP button (C).
9.
Press the TRIM/TEST button (J) and the CYCLE button (H). The machine will make a trim and
a test cut. Adjust the down feed rate of the head, using the flow control valve (N) while it is making
the first cut.
10.
Check the accuracy of the first part and make any adjustments required. The fine adjustment
knob (O) will change the length of the part by 1.5 thousandths of an inch per increment.
11.
Press the CYCLE button again and the machine will make another test cut.
12.
Set the counter (P) to the desired number of pieces. For instructions, REFER TO SECTION 6.9.
13.
After you have made all of the fine adjustments, place the AUTO/MANUAL switch in the AUTO
position and press the CYCLE button again. The machine will start the automatic operation and
continue until the counter reaches the set quantity or the machine runs out of material.
IMPORTANT: When the machine has finished a bar of material, you have to reset the machine
before continuing with the automatic operation. TO RESET THE MACHINE:
1.
Load the new bar in the machine with approximately 1/2 inch extending past the blade slot in the
material vise.
2.
Turn the AUTOMATIC/MANUAL switch (I) to the MANUAL position.
3.
Push the TRIM/TEST button (J) and then the CYCLE button (H). The saw will make one trim cut
and one test cut.
4.
Place the AUTOMATIC/MANUAL switch (I) in the AUTOMATIC position and press the
CYCLE button (H) and the saw will continue with the automatic operation.
CAUTION: FAILURE TO FOLLOW THE ABOVE PROCEDURE EVERY TIME THAT A
NEW BAR IS LOADED WILL CAUSE THE MACHINE TO MALFUNCTION.
Summary of Contents for CPO-315-HFA-5HP
