Page 29
►
NOTE: When punching larger diameter holes or alloy steels, set the down stroke of the machine
so that the punch stops just above the plane of the die, approximately fifteen thousandths
of an inch (.3mm). This will reduce the punching shock encountered in these applications.
Rated on mild steel having 65,000 psi tensile.
MAXIMUM MATERIAL THICKNESS IS 1 INCH (25MM).
FIGURE 10
HOLE DIAMETER
METAL
GAUGE
THICKNESS
INCHES
1/8
.125
3/16
.1875
1/4
.250
5/16
.3125
3/8
.375
7/16
.4375
1/2
.500
9/16
.5625
5/8
.625
11/16
.6875
3/4
.750
13/16
.8125
7/8
.875
15/16
.9375
1
1.00
28
.015
26
.018
24
.024
22
.030
20
.036
18
.048
16
.060
14
.075
12
.105
10
.135
.157
.188
.250
.375
.500
.625
.750
1.00
5/32
3/16
1/4
3/8
1/2
5/8
3/4
1
.2
.2
.3
.2
.2
.3
.4
.4
.4
.6
.5
.7
.6
.9
.7
1.0
.7
1.2
.8
1.3
.9
1.5
1.0
1.6
1.1
1.8
1.2
1.9
1.3
2.1
2.2
2.4
.4
.4
.5
.6
.7
.8
.9
1.0
1.1
1.1
1.2
1.3
1.4
.4
.5
.6
.7
.8
.9
1.1
1.2
1.3
1.4
1.5
1.6
.7
.9
1.1
1.2
1.4
1.6
1.8
2.1
2.3
2.5
2.6
2.8
.9
1.2
1.4
1.6
1.9
2.1
2.4
2.6
2.8
3.1
3.3
3.5
3.8
1.2
1.5
1.8
2.1
2.3
2.6
2.9
3.2
3.5
3.8
4.1
4.4
4.7
1.5
1.8
2.2
2.6
2.9
3.3
3.7
4.0
4.4
4.8
5.1
5.5
5.9
2.1
2.6
3.1
3.6
4.1
4.6
5.1
5.7
6.2
6.7
7.2
7.7
8.2
2.6
3.3
4.0
4.6
5.3
5.9
6.6
7.3
7.9
8.6
9.2
9.9
10.6
3.1
3.8
4.6
5.4
6.1
6.9
7.7
8.4
9.2
10.0
10.7
11.5
12.3
3.7
4.6
5.5
6.4
7.4
8.3
9.2
10.1
11.0
12.0
12.9
13.8
14.8
4.9
6.1
7.4
8.6
9.8
11.1
12.3
13.5
14.7
16.0
17.2
18.4
19.7
.5
.7
.9
1.1
1.5
2.0
2.3
2.8
.4
.5
.6
.7
1.0
1.3
.3
1.8
1.9
1.9
11.1
12.8
14.8
16.5
18.5
20.2
22.1
23.8
25.8
27.5
29.5
19.7
22.0
24.6
26.9
29.5
31.8
34.4
36.8
39.4
33.7
36.9
39.9
43.0
46.0
49.2
44.3
47.7
51.7
55.2
59.0
80.0
30.8
P R E S S U R E I N T O N S
TONS REQUIRED PER HOLE TO PUNCH MILD STEEL HAVING 65,000 PSI TENSILE STRENGTH
Summary of Contents for FI-8510-20M
