background image

EH330, EH430 and ECC Condensing Unit

Remote Low Side Cuber Service Manual

July 2013

Page 15

Condensing Unit Electrical

Route interconnecting control wire through proper 

hole in side of CU unit and plug into the connection on 

the side of the control box.

Route power conduit (liquid tight) and wires to the 

hole in the side of the CU unit. Connect to wire leads 

or terminal strip, if used, with the proper type of 

connector. 

Note: The power supply wires must be the correct 

size and type per the National Electric Code.

Locate the nameplate on the CU unit for the Voltage, 

Phase, Minimum Circuit Ampacity and Maximum Fuse 

Size. Either fuses or HACR type circuit breakers may 

be used.

Follow all Local, State and National Codes.

Three Phase Notice

: Check voltage between legs 

at contactor. If there is a “wild leg” in the three phase 

power supply move supply wires so the higher voltage 

is on L3 of the contactor, which connects to the 

compressor motor only.

Electrical Junction Box

Dataplate Location

Communication 

Cable

Connect Cable Here

Summary of Contents for ECC1200 Series


























































Reviews: