background image

General Safety Information

xvii

SCOTT SAFETY

087-0067 REV A

General Safety 
Information

Ensure you adhere to the following for your safety.

Warning: Read and follow the entire content of this guide prior to use. Failure to do 
so may result in serious injury or death.

Warning: All individuals who have or will have responsibility for using or testing this 
product must read and understand the contents of this manual. The product will 
perform as designed only if used and tested in accordance with the manufacturer's 
instructions. Failure to follow manufacturer's instructions will render the warranty 
and approvals null and void. Failure to follow these instructions may also result in 
serious injury or death.

Warning: Do not operate this equipment while under the influence of drugs, alcohol, 
or any medications or substances which may affect vision, dexterity, or judgment. 
Users of this equipment must be in good physical and mental health in order to 
operate safely. Do not use this equipment when fatigue prevents safe operation. Stay 
alert when operating this equipment. Inattention or carelessness while operating this 
equipment may result in serious injury or death.

Caution: Training is required before use of this equipment. Improper use may result in 
serious injury or death. Improper use includes, but is not limited to, use without 
adequate training, disregard of the warnings and instructions contained herein, use of 
the equipment for purposes not included in these instructions, and failure to inspect 
and maintain the equipment.

Caution: All electrical connections shall be installed by a qualified electrician in 
accordance with applicable electrical codes and shall include proper grounding of the 
equipment.

Caution: All service must be performed by qualified trained technicians. When 
servicing, disconnect power from the equipment and follow all necessary Lock-Out/ 
Tag-Out procedures and safety procedures.

Warning: Hot surfaces can cause serious injury. Allow the equipment to cool before 
servicing.

Caution: Establish a schedule for performing routine maintenance as outlined in 
these instructions.

Caution: Refer to the Material Safety Data Sheet (MSDS) for instructions on the safe 
handling of any chemicals used in the maintenance or servicing of this equipment.

Warning: Moving parts can cause serious injury. Be sure all guards and covers are in 
place and secure before starting the unit.

Warning: High pressure air is dangerous. Handle the high pressure air connections 
and hoses with care to prevent serious injury or death.

Caution: The air produced by this equipment must be recertified periodically as 
meeting CGA Grade D or better breathing quality air. Regular recertification to this 
standard is the responsibility of the user.

Summary of Contents for HushAir Connect 7500

























































































































Reviews: